[1] Wang H M. Materials’ fundamental issues of laser additive manufacturing for high-performance large metallic components[J]. Acta Aeronautica et Astronautica Sinica, 35, 2690-2698(2014).

[2] Wang H M, Zhang S Q, Wang X M. Progress and challenges of laser direct manufacturing of large titanium structural components(invited paper)[J]. Chinese Journal of Lasers, 36, 3204-3209(2009).

[3] Tang H B, Wu Y, Zhang S Q et al. Research status and development trend of high performance large metallic components by laser additive manufacturing technique[J]. Journal of Netshape Forming Engineering, 11, 58-63(2019).

[4] Yu Z B, Zhang Z B, Yin T T et al. Review of metal 3D printing technology[J]. Mechanical Management and Development, 37, 266-268(2022).

[5] Zhang X J, Tang S Y, Zhao H Y et al. Research status and key technologies of 3D printing[J]. Journal of Materials Engineering, 44, 122-128(2016).

[6] Zhao C, Fezzaa K, Cunningham R W et al. Real-time monitoring of laser powder bed fusion process using high-speed X-ray imaging and diffraction[J]. Scientific Reports, 7, 3602(2017).

[7] Gu D D, Meiners W, Wissenbach K et al. Laser additive manufacturing of metallic components: materials, processes and mechanisms[J]. International Materials Reviews, 57, 133-164(2012).

[8] Wu Z K, Zhang J, Wu S C et al. Application of in situ three-dimensional synchrotron radiation X-ray tomography for defects evaluation of metal additive manufactured components[J]. Nondestructive Testing, 42, 46-50(2020).

[9] An N Y, Shuai S S, Hu T et al. Application of synchrotron X-ray imaging and diffraction in additive manufacturing: a review[J]. Acta Metallurgica Sinica (English Letters), 35, 25-48(2022).

[10] Ioannidou C, König H H, Semjatov N et al. In-situ synchrotron X-ray analysis of metal additive manufacturing: current state, opportunities and challenges[J]. Materials & Design, 219, 110790(2022).

[11] Schröder J, Evans A, Mishurova T et al. Diffraction-based residual stress characterization in laser additive manufacturing of metals[J]. Metals, 11, 1830(2021).

[12] Liu Z P[M]. Introduction to physics of synchrotron radiation source, 1-10(2009).

[13] Li Y Z, Fan X X, Zeng G et al. The development of science and technology and scientific impact analysis on synchrotron radiation light source: a case study of ESRF[J]. World Sci-Tech R & D, 41, 16-31(2019).

[14] Sun W, Symes D R, Brenner C M et al. Review of high energy X-ray computed tomography for non-destructive dimensional metrology of large metallic advanced manufactured components[J]. Reports on Progress in Physics, 85, 016102(2022).

[15] Li N, Wang X, Liu C K. Research development of residual stress measured by neutron diffraction[J]. Failure Analysis and Prevention, 16, 148-154(2021).

[16] Xu X Y, Lü Y T, Zhang D et al. Measuring residual stress by neutron diffraction[J]. Materials Review, 29, 117-122(2015).

[17] Rietveld H M. The rietveld method[J]. Physica Scripta, 89, 098002(2014).

[18] Wei J. Brief introduction of spallation neutron source in China[J]. Modern Physics, 19, 22-29(2007).

[19] Wang Y D, Li R G, Nie Z H et al. A review on the application of neutron and high-energy X-ray diffraction characterization methods in engineering materials[J]. Chinese Journal of Engineering, 44, 676-689(2022).

[20] Sinclair L, Leung C L A, Marussi S et al. In situ radiographic and ex situ tomographic analysis of pore interactions during multilayer builds in laser powder bed fusion[J]. Additive Manufacturing, 36, 101512(2020).

[21] Chen Y H, Clark S J, Leung C L A et al. In-situ synchrotron imaging of keyhole mode multi-layer laser powder bed fusion additive manufacturing[J]. Applied Materials Today, 20, 100650(2020).

[22] Ahmed F F, Clark S J, Alex Leung C L et al. Achieving homogeneity in a high-Fe β-Ti alloy laser-printed from blended elemental powders[J]. Materials & Design, 210, 110072(2021).

[23] Robert O, Knut S, Bernhard H et al. Synchrotron μ-CT-based morphological characterization of additively manufactured open porous structures[J]. Additive Manufacturing, 55, 102874(2022).

[24] Leung C L A, Marussi S, Towrie M et al. Laser-matter interactions in additive manufacturing of stainless steel SS316L and 13-93 bioactive glass revealed by in situ X-ray imaging[J]. Additive Manufacturing, 24, 647-657(2018).

[25] Leung C L A, Marussi S, Atwood R C et al. In situ X-ray imaging of defect and molten pool dynamics in laser additive manufacturing[J]. Nature Communications, 9, 1355(2018).

[26] Leung C L A, Marussi S, Towrie M et al. The effect of powder oxidation on defect formation in laser additive manufacturing[J]. Acta Materialia, 166, 294-305(2019).

[27] Chen Y H, Clark S J, Sinclair L et al[EB/OL]. In situ and operando X-ray imaging of directed energy deposition additive manufacturing. https://arxiv.org/abs/2006.09087

[28] Chen Y H, Clark S J, Collins D M et al. Correlative synchrotron X-ray imaging and diffraction of directed energy deposition additive manufacturing[J]. Acta Materialia, 209, 116777(2021).

[29] Chen Y, Clark S, Leung A C L et al. Melt pool morphology in directed energy deposition additive manufacturing process[J]. IOP Conference Series: Materials Science and Engineering, 861, 012012(2020).

[30] Parab N D, Zhao C, Cunningham R et al. Ultrafast X-ray imaging of laser-metal additive manufacturing processes[J]. Journal of Synchrotron Radiation, 25, 1467-1477(2018).

[31] Hojjatzadeh S M H, Guo Q L, Parab N D et al. In-situ characterization of pore formation dynamics in pulsed wave laser powder bed fusion[J]. Materials, 14, 2936(2021).

[32] Gould B, Wolff S, Parab N et al. In situ analysis of laser powder bed fusion using simultaneous high-speed infrared and X-ray imaging[J]. JOM, 73, 201-211(2021).

[33] Simonds B J, Tanner J, Artusio-Glimpse A et al. The causal relationship between melt pool geometry and energy absorption measured in real time during laser-based manufacturing[J]. Applied Materials Today, 23, 101049(2021).

[34] Sun T, Tan W D, Chen L Y et al. In situ/operando synchrotron X-ray studies of metal additive manufacturing[J]. MRS Bulletin, 45, 927-933(2020).

[35] Paulson N H, Gould B, Wolff S J et al. Correlations between thermal history and keyhole porosity in laser powder bed fusion[J]. Additive Manufacturing, 34, 101213(2020).

[36] Zhao C, Guo Q L, Li X X et al. Bulk-explosion-induced metal spattering during laser processing[J]. Physical Review X, 9, 021052(2019).

[37] Martin A A, Calta N P, Hammons J A et al. Ultrafast dynamics of laser-metal interactions in additive manufacturing alloys captured by in situ X-ray imaging[J]. Materials Today Advances, 1, 100002(2019).

[38] Cunningham R, Zhao C, Parab N et al. Keyhole threshold and morphology in laser melting revealed by ultrahigh-speed X-ray imaging[J]. Science, 363, 849-852(2019).

[39] Zhao C, Parab N D, Li X X et al. Critical instability at moving keyhole tip generates porosity in laser melting[J]. Science, 370, 1080-1086(2020).

[40] Hojjatzadeh S M H, Parab N D, Yan W T et al. Pore elimination mechanisms during 3D printing of metals[J]. Nature Communications, 10, 3088(2019).

[41] Hojjatzadeh S M H, Parab N D, Guo Q L et al. Direct observation of pore formation mechanisms during LPBF additive manufacturing process and high energy density laser welding[J]. International Journal of Machine Tools and Manufacture, 153, 103555(2020).

[42] Young Z A, Guo Q L, Parab N D et al. Types of spatter and their features and formation mechanisms in laser powder bed fusion additive manufacturing process[J]. Additive Manufacturing, 36, 101438(2020).

[43] Li X X, Zhao C, Sun T et al. Revealing transient powder-gas interaction in laser powder bed fusion process through multi-physics modeling and high-speed synchrotron X-ray imaging[J]. Additive Manufacturing, 35, 101362(2020).

[44] Derimow N, Schwalbach E J, Benzing J T et al. In situ absorption synchrotron measurements, predictive modeling, microstructural analysis, and scanning probe measurements of laser melted Ti-6Al-4V single tracks for additive manufacturing applications[J]. Journal of Alloys and Compounds, 900, 163494(2022).

[45] Kantzos C A, Cunningham R W, Tari V et al. Characterization of metal additive manufacturing surfaces using synchrotron X-ray CT and micromechanical modeling[J]. Computational Mechanics, 61, 575-580(2018).

[46] Gan Z T, Kafka O L, Parab N et al. Universal scaling laws of keyhole stability and porosity in 3D printing of metals[J]. Nature Communications, 12, 2379(2021).

[47] Qu M L, Guo Q L, Escano L I et al. Controlling process instability for defect lean metal additive manufacturing[J]. Nature Communications, 13, 1079(2022).

[48] Guo Q L, Zhao C, Qu M L et al. In-situ full-field mapping of melt flow dynamics in laser metal additive manufacturing[J]. Additive Manufacturing, 31, 100939(2020).

[49] Guo Q L, Qu M L, Escano L I et al. Revealing melt flow instabilities in laser powder bed fusion additive manufacturing of aluminum alloy via in situ high-speed X-ray imaging[J]. International Journal of Machine Tools and Manufacture, 175, 103861(2022).

[50] Guo Q L, Zhao C, Escano L I et al. Transient dynamics of powder spattering in laser powder bed fusion additive manufacturing process revealed by in situ high-speed high-energy X-ray imaging[J]. Acta Materialia, 151, 169-180(2018).

[51] Guo Q L, Zhao C, Qu M L et al. In-situ characterization and quantification of melt pool variation under constant input energy density in laser powder bed fusion additive manufacturing process[J]. Additive Manufacturing, 28, 600-609(2019).

[52] Wu Z H, Basu D, Meyer J L L et al. Study of powder gas entrapment and its effects on porosity in 174 PH stainless steel parts fabricated in laser powder bed fusion[J]. JOM, 73, 177-188(2021).

[53] King W E, Barth H D, Castillo V M et al. Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing[J]. Journal of Materials Processing Technology, 214, 2915-2925(2014).

[54] Chen W Y, Zhang X, Li M M et al. Laser powder bed fusion of Inconel 718 on 316 stainless steel[J]. Additive Manufacturing, 36, 101500(2020).

[55] Tang G N, Gould B J, Ngowe A et al. An updated index including toughness for hot-cracking susceptibility[J]. Metallurgical and Materials Transactions A, 53, 1486-1498(2022).

[56] Jasien C, Saville A, Becker C G et al. In situ X-ray radiography and computational modeling to predict grain morphology in β-titanium during simulated additive manufacturing[J]. Metals, 12, 1217(2022).

[57] Wang H, Gould B, Haddad M et al. In situ X-ray imaging of directed energy deposition of metals: the comparisons of delivery performance between spherical and irregular powders[J]. Journal of Manufacturing Processes, 79, 11-18(2022).

[58] Wolff S J, Webster S, Parab N D et al. In-situ observations of directed energy deposition additive manufacturing using high-speed X-ray imaging[J]. JOM, 73, 189-200(2021).

[59] Wolff S J, Wang H, Gould B et al. In situ X-ray imaging of pore formation mechanisms and dynamics in laser powder-blown directed energy deposition additive manufacturing[J]. International Journal of Machine Tools and Manufacture, 166, 103743(2021).

[60] Wang H, Gould B, Moorehead M et al. In situ X-ray and thermal imaging of refractory high entropy alloying during laser directed deposition[J]. Journal of Materials Processing Technology, 299, 117363(2022).

[61] Pegues J W, Melia M A, Rodriguez M A et al. In situ synchrotron X-ray imaging and mechanical properties characterization of additively manufactured high-entropy alloy composites[J]. Journal of Alloys and Compounds, 876, 159505(2021).

[62] Wahlmann B, Krohmer E, Breuning C et al. In situ observation of γ’ phase transformation dynamics during selective laser melting of CMSX-4[J]. Advanced Engineering Materials, 23, 2100112(2021).

[63] Krohmer E, Schmeiser F, Wahlmann B et al. Revealing dynamic processes in laser powder bed fusion with in situ X-ray diffraction at PETRA III[J]. Review of Scientific Instruments, 93, 065104(2022).

[64] Schmeiser F, Krohmer E, Schell N et al. Experimental observation of stress formation during selective laser melting using in situ X-ray diffraction[J]. Additive Manufacturing, 32, 101028(2020).

[65] Uhlmann E, Krohmer E, Schmeiser F et al. A laser powder bed fusion system for in situ X-ray diffraction with high-energy synchrotron radiation[J]. Review of Scientific Instruments, 91, 075104(2020).

[66] Schmeiser F, Krohmer E, Schell N et al. Internal stress evolution and subsurface phase transformation in titanium parts manufactured by laser powder bed fusion: an in situ X-ray diffraction study[J]. Advanced Engineering Materials, 23, 2001502(2021).

[67] Epp J, Dong J, Meyer H et al. Analysis of cyclic phase transformations during additive manufacturing of hardenable tool steel by in situ X-ray diffraction experiments[J]. Scripta Materialia, 177, 27-31(2020).

[68] Calta N P, Wang J, Kiss A M et al. An instrument for in situ time-resolved X-ray imaging and diffraction of laser powder bed fusion additive manufacturing processes[J]. Review of Scientific Instruments, 89, 055101(2018).

[69] Thampy V, Fong A Y, Calta N P et al. Subsurface cooling rates and microstructural response during laser based metal additive manufacturing[J]. Scientific Reports, 10, 1981(2020).

[70] Martin A A, Calta N P, Khairallah S A et al. Dynamics of pore formation during laser powder bed fusion additive manufacturing[J]. Nature Communications, 10, 1987(2019).

[71] Calta N P, Martin A A, Hammons J A et al. Pressure dependence of the laser-metal interaction under laser powder bed fusion conditions probed by in situ X-ray imaging[J]. Additive Manufacturing, 32, 101084(2020).

[72] Kiss A M, Fong A Y, Calta N P et al. Laser-induced keyhole defect dynamics during metal additive manufacturing[J]. Advanced Engineering Materials, 21, 1970031(2019).

[73] Martin A A, Wang J, DePond P J et al. A laser powder bed fusion system for operando synchrotron X-ray imaging and correlative diagnostic experiments at the Stanford Synchrotron Radiation Lightsource[J]. The Review of Scientific Instruments, 93, 043702(2022).

[74] Calta N P, Thampy V, Lee D R C et al. Cooling dynamics of two titanium alloys during laser powder bed fusion probed with in situ X-ray imaging and diffraction[J]. Materials & Design, 195, 108987(2020).

[75] Hocine S, van Petegem S, Frommherz U et al. A miniaturized selective laser melting device for operando X-ray diffraction studies[J]. Additive Manufacturing, 34, 101194(2020).

[76] Hocine S, van Swygenhoven H, van Petegem S et al. Operando X-ray diffraction during laser 3D printing[J]. Materials Today, 34, 30-40(2020).

[77] Ghasemi-Tabasi H E, de Formanoir C, van Petegem S et al. Direct observation of crack formation mechanisms with operando laser powder bed fusion X-ray imaging[J]. Additive Manufacturing, 51, 102619(2022).

[78] Glerum J A, Hocine S, Chang C S T et al. Operando X-ray diffraction study of thermal and phase evolution during laser powder bed fusion of Al-Sc-Zr elemental powder blends[J]. Additive Manufacturing, 55, 102806(2022).

[79] Dass A, Gabourel A, Pagan D et al. Laser based directed energy deposition system for operando synchrotron X-ray experiments[J]. The Review of Scientific Instruments, 93, 075106(2022).

[80] Zhang X X, Lutz A, Andrä H et al. Strain hardening behavior of additively manufactured and annealed AlSi3.5Mg2.5 alloy[J]. Journal of Alloys and Compounds, 898, 162890(2022).

[81] An K, Yuan L, Dial L et al. Neutron residual stress measurement and numerical modeling in a curved thin-walled structure by laser powder bed fusion additive manufacturing[J]. Materials & Design, 135, 122-132(2017).

[82] Sofras C, ACˇGapek J, Arabi-Hashemi A et al. Tailored deformation behavior of 304L stainless steel through control of the crystallographic texture with laser-powder bed fusion[J]. Materials & Design, 219, 110789(2022).

[83] Pant P, Salvemini F, Proper S et al. A study of the influence of novel scan strategies on residual stress and microstructure of L-shaped LPBF IN718 samples[J]. Materials & Design, 214, 110386(2022).

[84] Tang L, Magdysyuk O, Jiang F Q et al. Mechanical performance and deformation mechanisms at cryogenic temperatures of 316L stainless steel processed by laser powder bed fusion: in situ neutron diffraction[J]. Scripta Materialia, 218, 114806(2022).

[85] Masoomi M, Shamsaei N, Winholtz R A et al. Residual stress measurements via neutron diffraction of additive manufactured stainless steel 174 PH[J]. Data in Brief, 13, 408-414(2017).

[86] Reid M, Sercombe T, Paradowska A et al. Residual stresses in selective laser melted components of different geometries[J]. Materials Research Proceedings, 2, 383-388(2017).

[87] Nadammal N, Cabeza S, Mishurova T et al. Effect of hatch length on the development of microstructure, texture and residual stresses in selective laser melted superalloy Inconel 718[J]. Materials & Design, 134, 139-150(2017).

[88] Luzin V, Kirstein O, Zahiri S H et al. Residual stress buildup in Ti components produced by cold spray additive manufacturing (CSAM)[J]. Journal of Thermal Spray Technology, 29, 1498-1507(2020).

[89] Shen C, Ma Y, Reid M et al. Neutron diffraction residual stress determinations in titanium aluminide component fabricated using the twin wire-arc additive manufacturing[J]. Journal of Manufacturing Processes, 74, 141-150(2022).

[90] Hasani N, Ghoncheh M H, Kindermann R M et al. Dislocations mobility in superalloy-steel hybrid components produced using wire arc additive manufacturing[J]. Materials & Design, 220, 110899(2022).

[91] Honnige J R, Williams S, Roy M J et al. Residual stress characterization and control in the additive manufacture of large scale metal structures[J]. Materials Research Proceedings, 2, 455-460(2017).

[92] Kim Y S, Chae H, Woo W et al. Multiple deformation scheme in direct energy deposited CoCrNi medium entropy alloy at 210 K[J]. Materials Science and Engineering: A, 828, 142059(2021).

[93] Wang Z Q, Stoica A D, Ma D et al. Diffraction and single-crystal elastic constants of Inconel 625 at room and elevated temperatures determined by neutron diffraction[J]. Materials Science and Engineering: A, 674, 406-412(2016).

[94] Wang Z Q, Denlinger E, Michaleris P et al. Residual stress mapping in Inconel 625 fabricated through additive manufacturing: method for neutron diffraction measurements to validate thermomechanical model predictions[J]. Materials & Design, 113, 169-177(2017).

[95] Ma D, Stoica A D, Wang Z Q et al. Crystallographic texture in an additively manufactured nickel-base superalloy[J]. Materials Science and Engineering: A, 684, 47-53(2017).

[96] Kirkwood H J, Zhang S Y, Tremsin A S et al. High resolution imaging and analysis of residual elastic strain in an additively manufactured turbine blade[J]. International Journal of Nanotechnology, 14, 166-178(2016).

[97] Cakmak E, Kirka M M, Watkins T R et al. Microstructural and micromechanical characterization of IN718 theta shaped specimens built with electron beam melting[J]. Acta Materialia, 108, 161-175(2016).

[98] Xie Q, Song G, Gorti S et al. Applying neutron transmission physics and 3D statistical full-field model to understand 2D Bragg-edge imaging[J]. Journal of Applied Physics, 123, 074901(2018).

[99] Hrabe N, Gnäupel-Herold T, Quinn T. Fatigue properties of a titanium alloy (Ti-6Al-4V) fabricated via electron beam melting (EBM): effects of internal defects and residual stress[J]. International Journal of Fatigue, 94, 202-210(2017).

[100] Cao J, Gharghouri M A, Nash P. Finite-element analysis and experimental validation of thermal residual stress and distortion in electron beam additive manufactured Ti-6Al-4V build plates[J]. Journal of Materials Processing Technology, 237, 409-419(2016).

[101] Clausen B, Brown D W, Carpenter J S et al. Deformation behavior of additively manufactured GP1 stainless steel[J]. Materials Science and Engineering: A, 696, 331-340(2017).

[102] Ghasri-Khouzani M, Peng H, Rogge R et al. Experimental measurement of residual stress and distortion in additively manufactured stainless steel components with various dimensions[J]. Materials Science and Engineering: A, 707, 689-700(2017).

[103] Zhang X, Yocom C J, Mao B et al. Microstructure evolution during selective laser melting of metallic materials: a review[J]. Journal of Laser Applications, 31, 031201(2019).

[104] Jakumeit J, Zheng G Y, Laqua R et al. Modelling the complex evaporated gas flow and its impact on particle spattering during laser powder bed fusion[J]. Additive Manufacturing, 47, 102332(2021).

[105] Wei H L, Mukherjee T, Zhang W et al. Mechanistic models for additive manufacturing of metallic components[J]. Progress in Materials Science, 116, 100703(2021).

[106] Bobel A, Hector L G Jr, Chelladurai I et al. In situ synchrotron X-ray imaging of 4140 steel laser powder bed fusion[J]. Materialia, 6, 100306(2019).

[107] Krakhmalev P, Fredriksson G, Yadroitsava I et al. Deformation behavior and microstructure of Ti6Al4V manufactured by SLM[J]. Physics Procedia, 83, 778-788(2016).

[108] Carlton H D, Haboub A, Gallegos G F et al. Damage evolution and failure mechanisms in additively manufactured stainless steel[J]. Materials Science and Engineering: A, 651, 406-414(2016).

[109] Tammas-Williams S, Zhao H, Léonard F et al. XCT analysis of the influence of melt strategies on defect population in Ti-6Al-4V components manufactured by selective electron beam melting[J]. Materials Characterization, 102, 47-61(2015).

[110] Tammas-Williams S, Withers P J, Todd I et al. The effectiveness of hot isostatic pressing for closing porosity in titanium parts manufactured by selective electron beam melting[J]. Metallurgical and Materials Transactions A, 47, 1939-1946(2016).

[111] Tammas-Williams S, Withers P J, Todd I et al. Porosity regrowth during heat treatment of hot isostatically pressed additively manufactured titanium components[J]. Scripta Materialia, 122, 72-76(2016).

[112] Wu S C, Hu Y N, Song Z et al. Fatigue behaviors of laser hybrid welded AA7020 due to defects via synchrotron X-ray microtomography[J]. Fatigue & Fracture of Engineering Materials & Structures, 42, 2232-2246(2019).

[113] Bao J G, Wu S C, Withers P J et al. Defect evolution during high temperature tension-tension fatigue of SLM AlSi10Mg alloy by synchrotron tomography[J]. Materials Science and Engineering: A, 792, 139809(2020).

[114] Hu D Y, Pan J C, Mao J X et al. Mechanical behavior prediction of additively manufactured components based on defect evolution observation by synchrotron radiation X-ray tomography[J]. Materials & Design, 198, 109353(2021).

[115] Qian W J, Wu S C, Wu Z K et al. In situ X-ray imaging of fatigue crack growth from multiple defects in additively manufactured AlSi10Mg alloy[J]. International Journal of Fatigue, 155, 106616(2022).

[116] Mercelis P, Kruth J P. Residual stresses in selective laser sintering and selective laser melting[J]. Rapid Prototyping Journal, 12, 254-265(2006).

[117] Serrano-Munoz I, Fritsch T, Mishurova T et al. On the interplay of microstructure and residual stress in LPBF IN718[J]. Journal of Materials Science, 56, 5845-5867(2021).

[118] Zhu B, Leung N, Kockelmann W et al. Revealing the residual stress distribution in laser welded Eurofer97 steel by neutron diffraction and Bragg edge imaging[J]. Journal of Materials Science & Technology, 114, 249-260(2022).

[119] Matsushima M, Jin X J, Shiota Y et al. Neutron diffraction measurement of thermal residual stresses caused by solution treatment for a SUS304 stainless steel mechanical part[M]. Sung J H, Lee C G, You Y Z, et al. Solid state phenomena, 425-430(2006).

[120] Jiang W C, Wan Y, Tu S T et al. Determination of the through-thickness residual stress in thick duplex stainless steel welded plate by wavelength-dependent neutron diffraction method[J]. International Journal of Pressure Vessels and Piping, 196, 104603(2022).

[121] Aminforoughi B, Degener S, Richter J et al. A novel approach to robustly determine residual stress in additively manufactured microstructures using synchrotron radiation[J]. Advanced Engineering Materials, 23, 2100184(2021).

[122] Xu W, Brandt M, Sun S et al. Additive manufacturing of strong and ductile Ti-6Al-4V by selective laser melting via in situ martensite decomposition[J]. Acta Materialia, 85, 74-84(2015).

[123] Rangaswamy P, Holden T M, Rogge R B et al. Residual stresses in components formed by the laserengineered net shaping (LENS®) process[J]. The Journal of Strain Analysis for Engineering Design, 38, 519-527(2003).

[124] Shen J J, Zeng Z, Nematollahi M et al. In-situ synchrotron X-ray diffraction analysis of the elastic behaviour of martensite and H-phase in a NiTiHf high temperature shape memory alloy fabricated by laser powder bed fusion[J]. Additive Manufacturing Letters, 1, 100003(2021).

[125] Wahlmann B, Galgon F, Stark A et al. Growth and coarsening kinetics of gamma prime precipitates in CMSX-4 under simulated additive manufacturing conditions[J]. Acta Materialia, 180, 84-96(2019).

[126] Beese A M, Wang Z Q, Stoica A D et al. Absence of dynamic strain aging in an additively manufactured nickel-base superalloy[J]. Nature Communications, 9, 2083(2018).

[127] Mori M, Yamanaka K, Onuki Y et al. Analysis of hierarchical microstructural evolution in electron beam powder bed fusion Ti-6Al-4V alloys via time-of-flight neutron diffraction[J]. Additive Manufacturing Letters, 3, 100053(2022).

[128] Xie Y, Vogel S C, Harp J M et al. Microstructure evolution of U-Zr system in a thermal cycling neutron diffraction experiment: extruded U-10Zr (wt. %)[J]. Journal of Nuclear Materials, 544, 152665(2021).

[129] Miao Y B, Mo K, Park J S et al. In situ synchrotron tensile investigations on ultrasonic additive manufactured (UAM) zirconium[J]. Journal of Nuclear Materials, 568, 153843(2022).

[130] Prasad K, Horita Y, Ito A et al. In situ synchrotron diffraction study of a crack-free additively manufactured Ni base superalloy[J]. Scripta Materialia, 200, 113896(2021).

[131] Gao Y B, Ding Y T, Li H F et al. Effect of deformation rate on the elastic-plastic deformation behavior of GH3625 alloy[J]. Acta Metallurgica Sinica, 58, 695-708(2022).

[132] Ashby M F. The deformation of plastically non-homogeneous materials[J]. The Philosophical Magazine: A Journal of Theoretical Experimental and Applied Physics, 21, 399-424(1970).

[133] Laquai R, Müller B R, Schneider J A et al. Using SXRR to probe the nature of discontinuities in SLM additive manufactured Inconel 718 specimens[J]. Metallurgical and Materials Transactions A, 51, 4146-4157(2020).

[134] Li X S, Zweiacker K, Grolimund D et al. In situ and ex situ characterization of the microstructure formation in Ni-Cr-Si alloys during rapid solidification: toward alloy design for laser additive manufacturing[J]. Materials, 13, 2192(2020).

[135] Wei Z Y, Zang L H, Fan W et al. Study of biological materials by neutron scattering[J]. Nuclear Techniques, 29, 713-720(2006).

[136] Fitzpatrick M E, Lodini A. Book review: analysis of residual stress by diffraction using neutron and synchrotron radiation[J]. Measurement Science and Technology, 14, 1739-1740(2003).