[1] Hussain S, Nazir A, Waqar S et al. Effect of additive manufactured hybrid and functionally graded novel designed cellular lattice structures on mechanical and failure properties[J]. The International Journal of Advanced Manufacturing Technology, 128, 4873-4891(2023).

[2] Eichenhofer M, Wong J C H, Ermanni P. Continuous lattice fabrication of ultra-lightweight composite structures[J]. Additive Manufacturing, 18, 48-57(2017).

[3] Chougrani L, Pernot J P, Véron P et al. Lattice structure lightweight triangulation for additive manufacturing[J]. Computer-Aided Design, 90, 95-104(2017).

[4] Abe T, Sasahara H. Layer geometry control for the fabrication of lattice structures by wire and arc additive manufacturing[J]. Additive Manufacturing, 28, 639-648(2019).

[5] Clausen A, Aage N, Sigmund O. Exploiting additive manufacturing infill in topology optimization for improved buckling load[J]. Engineering, 2, 250-257(2016).

[6] Hu J D, Tan A T L, Chen H et al. Superior compressive properties of 3D printed plate lattice mechanical metamaterials[J]. International Journal of Mechanical Sciences, 231, 107586(2022).

[7] Aremu A O, Brennan-Craddock J P J, Panesar A et al. A voxel-based method of constructing and skinning conformal and functionally graded lattice structures suitable for additive manufacturing[J]. Additive Manufacturing, 13, 1-13(2017).

[8] Tancogne-Dejean T, Spierings A B, Mohr D. Additively-manufactured metallic micro-lattice materials for high specific energy absorption under static and dynamic loading[J]. Acta Materialia, 116, 14-28(2016).

[9] Qiao P Z, Yang M J, Bobaru F. Impact mechanics and high-energy absorbing materials: review[J]. Journal of Aerospace Engineering, 21, 235-248(2008).

[10] Plocher J, Panesar A. Mechanical performance of additively manufactured fiber-reinforced functionally graded lattices[J]. JOM, 72, 1292-1298(2020).

[11] Andrews E W, Gibson J, Ashby M F. The creep of cellular solids[J]. Acta Materialia, 47, 2853-2563(1999).

[12] Zeng S J, Liu G, Li C S et al. Porous structure design and mechanical properties analysis of femoral stem based on selective laser melting[J]. Chinese Journal of Lasers, 49, 0202016(2022).

[13] Tang L T, Liu F C, You Q F et al. Compression performance of selective laser melting-fabricated lattice structures with different strut angles[J]. Chinese Journal of Lasers, 51, 2402301(2024).

[14] Maskery I, Hussey A, Panesar A et al. An investigation into reinforced and functionally graded lattice structures[J]. Journal of Cellular Plastics, 53, 151-165(2017).

[15] Hu J B, Wang S F, Wang Y et al. A lightweight methodology of 3D printed objects utilizing multi-scale porous structures[J]. The Visual Computer, 35, 949-959(2019).

[16] Rodrigo C, Xu S Q, Durandet Y et al. Quasi-static and dynamic compression of additively manufactured functionally graded lattices: experiments and simulations[J]. Engineering Structures, 284, 115909(2023).

[17] Wang Y, Liu F, Zhang X Y et al. Cell-size graded sandwich enhances additive manufacturing fidelity and energy absorption[J]. International Journal of Mechanical Sciences, 211, 106798(2021).

[18] An X Y, Lai C L, Fan H L et al. 3D acoustic metamaterial-based mechanical metalattice structures for low-frequency and broadband vibration attenuation[J]. International Journal of Solids and Structures, 191, 293-306(2020).

[19] Al-Ketan O, Ali M, Khalil M et al. Forced convection computational fluid dynamics analysis of architected and three-dimensional printable heat sinks based on triply periodic minimal surfaces[J]. Journal of Thermal Science and Engineering Applications, 13, 021010(2021).

[20] Li D W, Liao W H, Dai N et al. Optimal design and modeling of gyroid-based functionally graded cellular structures for additive manufacturing[J]. Computer-Aided Design, 104, 87-99(2018).

[21] Nie W, Liu F C, Hu W W et al. Effect of pore type on high‑temperature plasticity of Inconel 625 alloy fabricated by selective laser melting[J]. Chinese Journal of Lasers, 51, 1002323(2024).

[22] Bai Y C, Wang D, Yang Y Q et al. Effect of heat treatment on the microstructure and mechanical properties of maraging steel by selective laser melting[J]. Materials Science and Engineering: A, 760, 105-117(2019).

[23] Maskery I, Aboulkhair N T, Aremu A O et al. A mechanical property evaluation of graded density Al-Si10-Mg lattice structures manufactured by selective laser melting[J]. Materials Science and Engineering: A, 670, 264-274(2016).

[24] Surmeneva M A, Surmenev R A, Chudinova E A et al. Fabrication of multiple-layered gradient cellular metal scaffold via electron beam melting for segmental bone reconstruction[J]. Materials & Design, 133, 195-204(2017).

[25] Fousová M, Vojtěch D, Kubásek J et al. Promising characteristics of gradient porosity Ti-6Al-4V alloy prepared by SLM process[J]. Journal of the Mechanical Behavior of Biomedical Materials, 69, 368-376(2017).

[26] Zhang M K. Optimization design of hidden curved surface gradient porous structure and study on mechanical Properties of laser selective melting forming[D](2020).

[27] Feng E H, Chen R, Di S X et al. Effect of heat treatment on microstructure and mechanical properties of TC4 alloy by selective laser melting[J]. Chinese Journal of Lasers, 51, 1002321(2024).

[28] Xu S Q, Shen J H, Zhou S W et al. Design of lattice structures with controlled anisotropy[J]. Materials & Design, 93, 443-447(2016).

[29] Chen X Y, Tan H F. An effective length model for octet lattice[J]. International Journal of Mechanical Sciences, 140, 279-287(2018).

[30] Yang E, Leary M, Lozanovski B et al. Effect of geometry on the mechanical properties of Ti-6Al-4V gyroid structures fabricated via SLM: a numerical study[J]. Materials & Design, 184, 108165(2019).

[31] Gao F C, Zeng Q L, Wang J et al. Compressive properties and energy absorption of BCC lattice structures with bio-inspired gradient design[J]. Acta Mechanica Sinica, 38, 421345(2022).