[1] Guo M, Dai Y F, Huang B D. Application status and development of laser powder bed fusion technology in typical electromechanical aviation products[J]. Chinese Journal of Lasers, 50, 1602304(2023).

[2] Uçak N, Çiçek A, Aslantas K. Machinability of 3D printed metallic materials fabricated by selective laser melting and electron beam melting: a review[J]. Journal of Manufacturing Processes, 80, 414-457(2022).

[3] Guo X X, Chen Z H. Numerical simulation of laser additive manufacturing process: a review[J]. Acta Aeronautica et Astronautica Sinica, 42, 524227(2021).

[4] Kasperovich G, Haubrich J, Gussone J et al. Correlation between porosity and processing parameters in TiAl6V4 produced by selective laser melting[J]. Materials & Design, 105, 160-170(2016).

[5] Liu Y, Yang Y Q, Mai S Z et al. Investigation into spatter behavior during selective laser melting of AISI 316L stainless steel powder[J]. Materials & Design, 87, 797-806(2015).

[6] Zheng H, Li H X, Lang L H et al. Effects of scan speed on vapor plume behavior and spatter generation in laser powder bed fusion additive manufacturing[J]. Journal of Manufacturing Processes, 36, 60-67(2018).

[7] Andani M T, Dehghani R, Karamooz-Ravari M R et al. A study on the effect of energy input on spatter particles creation during selective laser melting process[J]. Additive Manufacturing, 20, 33-43(2018).

[8] Leuders S, Thöne M, Riemer A et al. On the mechanical behaviour of titanium alloy TiAl6V4 manufactured by selective laser melting: fatigue resistance and crack growth performance[J]. International Journal of Fatigue, 48, 300-307(2013).

[9] Yan Z R, Liu W W, Tang Z J et al. Effect of thermal characteristics on distortion in laser cladding of AISI 316L[J]. Journal of Manufacturing Processes, 44, 309-318(2019).

[10] Ali H, Ghadbeigi H, Mumtaz K. Processing parameter effects on residual stress and mechanical properties of selective laser melted Ti6Al4V[J]. Journal of Materials Engineering and Performance, 27, 4059-4068(2018).

[11] Ali H, Ma L, Ghadbeigi H et al. In-situ residual stress reduction, martensitic decomposition and mechanical properties enhancement through high temperature powder bed pre-heating of selective laser melted Ti6Al4V[J]. Materials Science and Engineering: A, 695, 211-220(2017).

[12] Ahsan F, Ladani L. Temperature profile, bead geometry, and elemental evaporation in laser powder bed fusion additive manufacturing process[J]. JOM, 72, 429-439(2020).

[13] Yang X, Li Y Z, Li B. Formation mechanisms of lack of fusion and keyhole-induced pore defects in laser powder bed fusion process: a numerical study[J]. International Journal of Thermal Sciences, 188, 108221(2023).

[14] Zheng Y J, Bian Q, Wang C et al. Technical study of microlens arrays for Gaussian beam homogenization shaping[J]. Chinese Journal of Lasers, 52, 0105002(2025).

[15] Qi Y, Zhu Y J, Zhang J et al. Research progress of laser beam shaping technology[J]. Laser & Optoelectronics Progress, 61, 0500005(2024).

[16] Gao H R, Li J K, Zhang Z W et al. Research status and prospect of multi-field modulated metal laser additive manufacturing (invited)[J]. Chinese Journal of Lasers, 51, 1002306(2024).

[17] Okunkova A, Volosova M, Peretyagin P et al. Experimental approbation of selective laser melting of powders by the use of non-Gaussian power density distributions[J]. Physics Procedia, 56, 48-57(2014).

[18] Okunkova A A, Peretyagin P Y, Podrabinnik P A et al. Development of laser beam modulation assets for the process productivity improvement of selective laser melting[J]. Procedia IUTAM, 23, 177-186(2017).

[19] Sow M C, de Terris T, Castelnau O et al. Influence of beam diameter on laser powder bed fusion (L-PBF) process[J]. Additive Manufacturing, 36, 101532(2020).

[20] Yuan W H, Chen H, Li S et al. Understanding of adopting flat-top laser in laser powder bed fusion processed Inconel 718 alloy: simulation of single-track scanning and experiment[J]. Journal of Materials Research and Technology, 16, 1388-1401(2022).

[21] Wang K, Xie D Q, Lv F et al. Stability of molten pool and microstructure evolution of Ti-6Al-4V during laser powder bed fusion with a flat-top beam[J]. Additive Manufacturing, 75, 103756(2023).

[22] Wang K, Xie D Q, Lv F et al. On the role of flat-top beam in pore elimination and fatigue performance of Ti-6Al-4V fabricated by laser powder bed fusion[J]. International Journal of Fatigue, 186, 108354(2024).

[23] Chen J, Jin M X, Wei K W et al. Laser-based powder bed fusion of nickel-based superalloy designed specifically for turbine blades using high-power flat-top laser: towards high-speed manufacturing and directional solidification[J]. Journal of Alloys and Compounds, 1022, 179902-179919(2025).

[24] Jodi D E, Kitashima T, Koizumi Y et al. Manufacturing single crystals of pure nickel via selective laser melting with a flat-top laser beam[J]. Additive Manufacturing Letters, 3, 100066(2022).

[25] Wang R, Wang J, Cao T W et al. Microstructure characteristics of a René N5 Ni-based single-crystal superalloy prepared by laser-directed energy deposition[J]. Additive Manufacturing, 61, 103363(2023).

[26] Jodi D E, Kitashima T, Singh A et al. High-temperature microstructural stability of pure Ni fabricated by laser powder bed fusion using Gaussian and flat-top beam profiles[J]. Materials Characterization, 200, 112897(2023).

[27] Syed A K, Ahmad B, Guo H et al. An experimental study of residual stress and direction-dependence of fatigue crack growth behaviour in as-built and stress-relieved selective-laser-melted Ti6Al4V[J]. Materials Science and Engineering: A, 755, 246-257(2019).

[28] Guo C, Li G, Li S et al. Additive manufacturing of Ni-based superalloys: residual stress, mechanisms of crack formation and strategies for crack inhibition[J]. Nano Materials Science, 5, 53-77(2023).

[29] Yakout M, Elbestawi M A, Veldhuis S C. A study of the relationship between thermal expansion and residual stresses in selective laser melting of Ti-6Al-4V[J]. Journal of Manufacturing Processes, 52, 181-192(2020).

[30] Chai Q, Zhang D Y, Zhang H et al. Numerical simulation of temperature field and stress field of laser cladding Stellite6[J]. Next Materials, 7, 100385(2025).

[31] Li M Y, Han B, Cai C B et al. Numerical simulation on temperature and stress fields of laser cladded Ni-based coating[J]. Transactions of the China Welding Institution, 36, 25-28, 32, 114(2015).

[32] Zhu C G, Sun Y N, Yu Q. Research state on numerical simulation of temperature field in laser cladding[J]. Hot Working Technology, 41, 132-134, 137(2012).

[33] Gao W Y, Zhao S S, Wang Y B et al. Effect of re-melting on the cladding coating of Fe-based composite powder[J]. Materials & Design, 64, 490-496(2014).

[34] Zheng X. SLM preparation of 316L stainless steel by laser remelting thermal coupling simulation and process optimization[D](2023).

[35] Li H Y, Song J L, Shi X L et al. Cladding process research progresses of numerical simulation of temperature field in laser[J]. Hot Working Technology, 51, 6-10, 16(2022).

[36] Zheng Z J, Zheng X. Temperature field simulation and process optimization of SLM forming of 316L stainless steel based on laser remelting[J]. Materials Reports, 38, 266-272(2024).

[37] Tenbrock C, Fischer F G, Wissenbach K et al. Influence of keyhole and conduction mode melting for top-hat shaped beam profiles in laser powder bed fusion[J]. Journal of Materials Processing Technology, 278, 116514(2020).

[38] Zhao J M, Lu L, Wang J R et al. Thermodynamic behavior and defects of laser selective melting Ti6Al4V at mesoscopic scale: numerical simulation and experimental verification[J]. Materials Reports, 35, 410-416(2021).

[39] Mahmood M A, Ur Rehman A, Azeem M M et al. On the development of part-scale FEM modeling for laser powder bed fusion of AISI 316L stainless steel with experimental verification[J]. The International Journal of Advanced Manufacturing Technology, 127, 2229-2255(2023).

[40] Mahmood M A, Ishfaq K, Oane M et al. Integrated approach for AlSi10Mg rapid part qualification: FEM, machine learning, and experimental verification in LPBF-based additive manufacturing process[J]. Progress in Additive Manufacturing, 10, 861-874(2025).

[41] Guirguis D, Tucker C, Beuth J. Machine learning for real-time detection of local heat accumulation in metal additive manufacturing[J]. Materials & Design, 241, 112933(2024).

[42] Chen Y, Guo Y B, Xu M J et al. Study on the element segregation and Laves phase formation in the laser metal deposited IN718 superalloy by flat top laser and Gaussian distribution laser[J]. Materials Science and Engineering: A, 754, 339-347(2019).

[43] Yi Y L, Wu H B, Jia C Z et al. Influence of interlayer laser remelting on residual stress during forming using selective laser melting[J]. Chinese Journal of Lasers, 50, 2402302(2023).

[44] Waqar S, Guo K, Sun J. FEM analysis of thermal and residual stress profile in selective laser melting of 316L stainless steel[J]. Journal of Manufacturing Processes, 66, 81-100(2021).

[45] Li Y L, Zhou K, Tan P F et al. Modeling temperature and residual stress fields in selective laser melting[J]. International Journal of Mechanical Sciences, 136, 24-35(2018).

[46] Tan P F, Shen F, Li B et al. A thermo-metallurgical-mechanical model for selective laser melting of Ti6Al4V[J]. Materials & Design, 168, 107642(2019).

[47] Liu S W, Zhu J J, Zhu H H et al. Effect of the track length and track number on the evolution of the molten pool characteristics of SLMed Al alloy: numerical and experimental study[J]. Optics & Laser Technology, 123, 105924(2020).