[1] FABRY S, SPODNIAK M, GASPAROVIC P et al. Aircraft gas turbine engine testing. Acta Avionica Journal, 21, 39-44(2019).

[2] ZHANG B C. Aero⁃engine test and measurement techno⁃ logy(2005).

[3] AI K B, WU Z Y, WEI H L et al. Aero⁃engine indoor test(2022).

[4] SHAN X M, GAO Q, WEI X L. Development analysis of aero⁃engine testing and measurement technology. Aviation Power, 67-70(2022).

[5] YANG Y. Measurement requirements and performance criteria for data acquisition in gas turbine engine testing(2009).

[6] WANG Z H, WANG L. Development of aero⁃engine tes⁃ ting measurement technology. Aeroengine, 40, 47-51(2014).

[7] BRIAN A B, DONAID J M, GRANT T P, al er. Aircraft propulsion system flight test⁃analysis and evaluation challenges and integrated solutions. Gas Turbines Power, 135(2013).

[8] JIANG S Q, GU T X. Measurement and condition monitoring system for key parameters of engines. Chinese Journal of Scientific Instrumentation, 26, 406-408(2005).

[9] ZHU R K, LIANG Q C, ZHAN H Y. Analysis of aero⁃engine performance and selection based on fuzzy comprehensive evaluation. Procedia Engineering, 174, 1202-1207(2017).

[10] DONG Y F. Principles and construction of general aeroen⁃gines(2021).

[11] YANG C, WU H, DU J et al. Numerical simulation of flow in aero⁃engine components and the whole engine. Journal of Engineering Thermophysics, 44, 894-902(2023).

[12] WU X H, HU X A, XIANG X et al. An analysis approach for micro gas turbine engine's performance by experiment and numerical simulation. Case Studies in Thermal Engineering, 49(2023).

[13] LI M Z, JI R M, HUANG X H. Aero⁃engine component characteristic correction based on improved Particle Swarm Optimization. Journal of Propulsion Technolo⁃ gy, 43, 411-419(2022).

[14] TSOUTSANIS S, MESKIN N, BENAMMAR M et al. Transient gas turbine performance diagnostics through nonlinear adaptation of compressor and turbine maps. Gas Turbines Power, 137(2015).

[15] EKICI S, SOHRET Y, COBAN K et al. Performance evaluation of an experimental turbojet engine. International Journal of Turbo and Jet Engines, 34(2017).

[16] WANG Y, LI Q H, HUANG X H. Design of an aero⁃engine limit protector based on ADRC. Journal of Beijing University of Aeronautics and Astronautics, 38, 1154-1157(2012).

[17] WANG Y S, DONG X M, LIU W et al. Research progress on high⁃temperature testing technology for aero⁃engines. Measurement and Control Technology, 36, 1-6(2017).

[18] ZHAO Y, LI B W, SONG H Q et al. Combined estimation method for the front temperature of high⁃pressure turbine in turbofan engines. Journal of Aerospace Power, 31, 3026-3033(2016).

[19] FOREST F, COCHARD Q, NOYER C. Large⁃scale vibration monitoring of aircraft engines from operational data using self⁃organized models(2020).

[20] GE X D, WU F Y, LIU Y Q et al. Research methods for whole aero⁃engine vibration and their engineering application. Acta Aeronautica et Astronautica Sinica, 45, 36-56(2024).

[21] DING X, FENG C Q, XUE W P et al. Force measurement method and calibration technology of aero⁃engine complete thrust test bed. Journal of Aerospace Power, 38, 144-150(2023).

[22] HUANG C, JIN C, QU J S et al. Thrust measurement and traceability system analysis of aero⁃engine indoor test bench. Metrology & Measurement Technology, 40, 16-20(2020).

[23] LIU Y L, QIN H F et al. Research on the influence of strain force sensor performance on thrust measurement. Metrology & Measurement Technology, 35, 88-89(2015).

[24] LI Z W, FENG W H, LIU R. Measurement error source analysis of dynamometer based on force sensor parallel mode. Metrology & Measurement Technology, 39, 65-69(2019).

[25] WU H M. Current status and prospects of thrust measurement calibration for jet and turbofan engine test bench. Metrology & Measurement Technology, 32, 1-3(2012).

[26] ZHU H J, DU F R, ZHAO S A et al. Design of a new type thrust measuring system for micro⁃turbojet engine, 133(2016).

[27] LIU Z, ZHANG S, YIN Y, al er. Research on thrust calibration technology of aeroengine indoor test bench. Journal of Applied Fluid Mechanics, 15, 109-116(2022).

[28] ZHANG Z, HOU A P, al er. Numerical simulation on thrust correction of an aero⁃engine in indoor engine test cell. Engineering Mechanics, 29, 308-313(2012).

[29] PARFITT P, BRISTOW M. Derivation of aerodynamic thrust correction for an indoor gas turbine engine test faci⁃lity using the "first principles" anemometer method(2006).

[30] GULLIA A, LASKARIDIS P, RAMSDEN K W et al. A preliminary investigation of thrust measurement correction in an enclosed engine test facility(2005).

[31] XING F, WU S L, ZHOU W et al. Numerical simulation study on thrust correction for outdoor test stand in natural wind. Journal of Propulsion Technology, 43, 363-370(2022).

[32] LU W R, WANG C Y, GAO F. Research on condition monitoring and fault diagnosis technology of dynamometer in aero⁃engine test bed(2022).

[33] LIU Z L, XU M W, ZHAO P et al. A power measurement system calibration technology based on the turboshaft engine test bed. Gas Turbine Experiment and Research, 31, 56-60(2018).

[34] FELIKS S, YEPIFANOV S, KOSTYANTYN P et al. New approach to torque measurement unit development and its calibration. Journal of KONBiN, 46, 75-86(2018).

[35] KANG J S, YANG S S. Modeling and experimental eva⁃luation of torque loss in turbine test rig for accurate turbine performance evaluation. Journal of Mechanical Science and Technology, 26, 473-479(2012).

[36] LI Y Q, LIU Z Q, XU D H et al. Development of magnetoelectric speed sensor for engine with high environment adaptability(2021).

[37] WANG H, JIANG H, LEI T et al. Study on the shape of cogging structure of rotor and stator with speed sensor(2022).

[38] LIO L T, HUANG X H, ZHANG T H et al. Integrated measurement of propeller pitch， phase angle and speed of turboprop engine based on new phonic wheel. Journal of Propulsion Technology, 43, 372-383(2022).

[39] HE Q L, DING L, CAI H W et al. Signal distortion prediction of magnetoelectric speed sensor. Chinese. Tournal of Sensors and Actuators, 36, 516-520(2023).

[40] SHAN X S, TANG L, WEN H et al. Analysis of vibration and acoustic signals for noncontact measurement of engine rotation speed. Sensors, 20(2020).

[41] DE LA TORRE E, HAINZ S. Advanced speed sensor for transmission systems. Elektrotechnik & Informationstechnik, 128, 415-420(2011).

[42] GUO S N, SUN C H, ZHANG S et al. Structural optimization to improve the performance of turbine flowmeter under different pressure conditions. Measurement, 220(2023).

[43] BASRI H, YANI I et al. Challenges in turbine flow metering system： an overview(2019).

[44] WANG S, ZHANG T H, WANG J F et al. Research on dynamic flow measurement method based on turbine flowmeter. Measurement and Control Technology, 31, 24-27(2012).

[45] YIN C, LI X L, GUO Z B et al. Experimental analysis of fuel consumption measurement and flow resistance characteristics of turbine flow sensors. China Measurement & Test, 45, 78-83(2019).

[46] LIU W G, XU Y, ZHANG T et al. Performance measurement analysis of various cone flow meters with various beta edge types and flow field parameters. Flow Measurement & Instrumentation, 45, 331-340(2015).

[48] CHEN M T, JIANG W Y, LIU W G et al. Research on V⁃cone flowmeter for aviation fuel flow measurement. Journal of Electronic Measurement and Instrumentation, 30, 1167-1174(2016).

[49] KOLHE V, EDLABADKAR R. An overview of coriolis mass flowmeter as a direct mass flowmeter as a direct mass. Journal on Emerging Trends in Technology, 3, 8-16(2023).

[50] GACE D A. On the performance of a Coriolis Mass Flowmeter （CMF）： experimental measurement and FSI simulation. International Journal of Metrology and Quality Engineering, 13(2022).

[51] PEI X X, CHEN Q F, SONG Y C et al. Theoretical and numerical analysis of U⁃shaped liquid hydrogen Coriolis mass flowmeter. Tianjin University Journal, 57, 992-1000(2024).

[52] LIAN M M, ZHENG J, LI Z et al. Numerical calculation and test of the influence of environmental vibration on coriolis flowmeter(2022).

[53] YANG Z, WANG Y, LIU L L et al. Design of non⁃intrusive engine intake flow pipe based on convergent⁃divergent throat structure. Metrology & Measurement Technolo⁃ gy, 43, 71-81(2023).

[54] SEVINC K. Aerodynamic design optimization of a bellmouth shaped air intake for jet engine testing purposes and its experiment based validation(2021).

[56] YU N X, WANG Y, LIU L L et al. Research on velocity profile of entrance section of bell⁃mouth flow tube. Metrology & Measurement Technology, 42, 102-110(2022).

[57] ZHAO H G, SHEN S C, ZHANG X F et al. Flight test of air flow measurement for turbofan engine. Journal of Aerospace Power, 42, 1778-1784(2022).

[58] DOLL U, MIGLIORINI M, BAIKIE J et al. Non⁃intrusive flow diagnostics for unsteady inlet flow distortion measurements in novel aircraft architectures. Progress in Aerospace Sciences, 130(2022).

[59] HE C, LIU Z, WANG Z et al. Effect of insert plate on the inlet pressure distortion of the aero⁃engine. Advances in Mechanical Engineering, 15(2023).

[60] KAKO S. A comparative study about accuracy levels of resistance temperature detectors RTDs composed of platinum， copper， and nickel. Al⁃Nahrain Journal for Engineering Sciences, 26, 216-225(2023).

[61] BAI G. Research on temperature measurement error of aero⁃engine inlet total temperature sensor. Measurement & Control Technology, 39, 76-83(2020).

[62] LI J, FAN D, JI C T et al. Method for improving the dynamic characteristics of aero⁃engine temperature sensors. Journal of Aerospace Power, 27, 707-714(2012).

[63] VILLAFANE L, PANIAGUA G. Aero⁃thermal analysis of shielded fine wire thermocouple probes. International Journal of Thermal Sciences, 65, 214-223(2013).

[64] YANG C, WU W L, XIONG Y B et al. Calibration technology of high temperature thermocouple at the outlet of aero⁃engine combustion chamber. Journal of Aerospace Power, 31, 769-774(2016).

[65] LV P F, PEI D X, SHEN D W et al. The research of transient thermometry technology based on k⁃Style thermocouple. Chinese Journal of Sensors and Actuators, 27, 775-780(2014).

[66] WANG T Z, REN K, ZHANG L et al. Analysis of the influence of NiCr⁃NiSi armoured thermocouple on temperature measurement accuracy. Measurement and Control Technology, 37, 320-323(2018).

[67] PURWAR A, DEEP S. A novel thermocouple for ultra⁃high temperature applications： design and computational analysis(2017).

[68] KOU Z H, WANG Q Y, LI G C et al. Thermocouple measurement technology for high temperature wall in aero⁃engine. Journal of Engineering for Thermal Energy and Power, 38, 202-210(2023).

[69] DONG X Y, XU W, ZHENG Q et al. Design of a total gas temperature sensor. Journal of Sensor Technology, 29, 301-305(2016).

[70] BIRCH B, BUTTSWORTH D, ZANDER F. Time⁃resolved stagnation temperature measurements in hypersonic flows using surface junction thermocouples. Experimental Thermal and Fluid Science, 119(2020).

[71] JI Z, DUAN F L, XIE Z. Transient measurement of temperature distribution using thin film thermocouple array on turbine blade surface. IEEE Sensors Journal, 21, 207-212(2021).

[72] RIVERA K, CRECORY O J. SiC ceramic matrix compo⁃ site thermocouples for engine components. IEEE Sensors Letters, 4(2020).

[73] ANUCHIN S A, LANIN A V, PROSUNTSOV P V et al. Influence of the method of attaching surface thermocouples on the error of temperature determination in testing ceramic materials on radiative heating installations. Journal of Engineering Physics and Thermophysics, 91, 585-593(2018).

[74] RUAN Y, XIAO Q, HAN Y N et al. High⁃precision NiCr / NiSi thin film thermocouple high temperature testing system. Instrument Technology and Sensors, 1-5， 10(2024).

[75] XIONG Q R, XU Y, LI H D et al. The influence of peak time in aero⁃engine tests on the temperature measurement of thermochromic paint. Gas Turbine Experiment and Research, 29, 30-34(2016).

[76] HU M, GE J F, XUE X S et al. Temperature indicating paint interpretation method based on image processing and K⁃nearest neighbor algorithm. Aeroengine, 47, 80-84(2021).

[77] WANG C, GOU X K, DUAN Y et al. A review of temperature measurement for aero⁃engine turbine blades. Infrared and Millimeter Waves, 37, 501-512(2018).

[78] PANAS A J, SZCZEPANIAK R, STRYCZNIEWICZ W et al. Thermophysical properties of temperature⁃sensitive paint. Materials, 14(2021).

[79] LIU J Y, QUAN Y K, XU G Q et al. Research progress on phosphor thermometry technology for aero⁃engine hot section component. Journal of Aerospace Power, 38, 2861-2871(2023).

[80] ERASMUS L J B, TERBLANS J J, SWART H C. Development of an optical thermometry system for phosphor materials. Vacuum, 155, 702-711(2018).

[81] SU W C, PENG X, LIU C Y et al. Method of infrared temperature measurement of high temperature components in gas environment. Aeroengine, 49, 163-168(2023).

[82] GAO S, ZHANG X Q, CHEN L W et al. Review： radiation temperature measurement methods for engine turbine blades and environment influence. Infrared Physics & Technology, 123(2022).

[83] HOTS N, PRAKUDA V, PAZUR A et al. Simulation of the temperature measurement by infrared radiation of the aircrafts'gas turbine engine(2022).

[84] LIU Y Y, JIA P G, YUAN S H. Design of an optical fiber composite probe for engine intake total temperature and total pressure. Infrared and Laser Engineering, 51, 34-41(2022).

[85] SEMMELMAYER F, REEDER M, SEYMOUR R. Determination of a probability distribution for pressure scanner noise and digitization uncertainty reporting. Measurement Science and Technology, 30(2019).

[86] ZHANG K, ZHANG S F. Research and experimental application of distributed large⁃scale integrated pressure measurement system. Navigation and Control, 14, 110-112(2015).

[87] WANG H, ZENG Q H. Research progress on pressure scanning valve pressure measurement system. Aerospace Metrology & Measurement Technology, 41, 76-81(2021).

[88] LIM K T, YOON S Y, GOYNE C P et al. Design and characterization of a centrifugal compressor surge test rig. International Journal of Rotating Machinery, 22(2011).

[89] LIU Y, YANG X F, XIONG Y. Progress in experimental research on thermoacoustic oscillations in gas turbine combustion fields. Spectroscopy and Spectral Analysis, 44, 3008-3019(2024).

[90] WANG C C, CAI J, WANG H B et al. The influence of temperature on the dynamic characteristics of the pressure tubing. Metrology & Measurement Technology, 38, 22-25(2018).

[91] GONG Z J, SHAO Z Q, SU L H et al. High⁃temperature dynamic pressure sensor based on piezoelectricity with pressure induction method. Sensors and Microsystems, 42, 110-112， 119(2023).

[92] SVETE A, KUTIN J. Optimal dimensions of connecting tubes for dynamic measurements of pressure, 1065(2018).

[93] XU L C, WANG X H, LIU Y P et al. Dynamic response characteristics of semi⁃infinite pressure tube. Journal of Aerospace Power, 39, 93-103(2024).

[94] HURST A M, VANDEWEERT J. An experimental and theoretical investigation of wave propagation in teflon and nylon tubing with methods to prevent aliasing in pressure scanners. Journal of Engineering for Gas Turbines and Power, 135(2013).

[95] LI B, YANG J, ZHANG H Y et al. Research on dynamic calibration technology of pressure measurement system with a pressure tubing cavity. Metrology & Measurement Technology, 41, 149-154(2021).

[96] WANG C C, WANG H B, SHI B. Influence of the gas medium on the metrological characteristics of shock tubes(2018).

[97] WANG T Z, ZHOU Z Y, LI W et al. Research and application progress of high⁃temperature piezoelectric vibration sensors and ceramic materials. Sensors and Microsystems, 39, 1-4(2020).

[98] BILGUNDE P N, BOND L J. Resonance analysis of a high temperature piezoelectric disc for sensitivity characterization. Ultrasonics, 87, 103-111(2018).

[99] WANG T Z, ZHANG J W, ZHANG L et al. Design research on IEPE type piezoelectric vibration sensor with anti⁃electromagnetic wide frequency response. Journal of Sensor Technology, 36, 9-14(2023).

[100] HOU L L, CAO S Q. Evaluation method for vibration measurement on casing in aeroengine： theoretical analysis and experimental study. Shock and Vibration, 2019.

[101] WANG Y K, ZHANG Z S, LIAO M F et al. Section selecting I or engine vibration measurement based on dynamic analysis. Journal of Aerospace Power, 33, 1446-1455(2018).

[102] SZYMAŃSKI G M, MISZTAL W. Analysis of measurement points sensitivity of vibration signals on the stand of jet engine. Combustion Engines, 171, 279-282(2017).

[103] ZHAO J M, HAO X L. Investigation of the vibration transmission characteristics of the aero⁃Engine casing system by rotating force exciter. Energies, 16(2023).