[1] [1] M. P. Pawar, G. Ranjan. On the effect of matrix cracks in composite helicopter rotor blade ［J］. Composites Science and Technol., 2005, 65(3-4): 581～594

[2] [2] N. Aretakis, K. Mathioudakis, V. Dedoussis. Derivation of signatures for faults in gas turbine compressor blading ［J］. Control Engineering Practice, 1998, 6(8): 969～974

[3] [3] A. King, A. Steuwer, C. Woodward et al.. Effects of fatigue and fretting on residual stresses introduced by laser shock peening ［J］. Materials Science and Engineering A, 2006, 435-436: 12～18

[4] [4] Gu Yongyu, Zhang Lingfeng, Lu Jinzhong et al.. Micro-plastic deformation of ZrO2 in high strain rate by laser shocking [J]. Chinese J. Lasers, 2009, 36(12): 3318～3322

[5] [5] C. S. Montross, L. Ye. Laser shock processing and its effects on microstructure and properties of metal alloys: a review [J]. International J. Fatigue, 2002, 24: 1021～1036

[6] [6] Luo Xinmin, Zhang Jingwen, Zhao Guangzhi et al.. Effect of laser shock strengthening on fatigue behaviors of 2A02 aluminum alloy [J]. Chinese J. Lasers, 2009, 36(12): 3323～3328

[7] [7] C. Rubio-González, J. L. Ocańa, G. Gomez-Rosas et al.. Effect of laser shock processing on fatigue crack growth and fracture toughness of 6061-T6 aluminum alloy ［J］. Materials Science and Engineering A, 2004, 386: 291～295

[8] [8] Zhang Yongkang, Chen Jufang, Xu Renjun. Experimental research of laser shock strengthening AM50 magnesium alloy [J]. Chinese J. Lasers, 2008, 35(7): 1668～1072

[9] [9] J. M. Yang, Y. C. Her, N. Han et al.. Laser shock peening on fatigue behavior of 2024-T3 Al alloy with fastener holes and stopholes ［J］. Materials Science and Engineering A, 2001, 298: 296～299

[10] [10] L. Harold, R. H. Michael. The effects of laser peening on high-cycle fatigue in 7085-T7651 aluminum alloy ［J］. Materials Science and Engineering A, 2008, 477(1-2): 208～216

[11] [11] M. Hakamada, Y. Nakamoto, H. Matsumoto et al.. Relationship between hardness and grain size in electrodeposited copper films ［J］. Materials Science and Engineering A, 2007, 457: 120～126

[12] [12] A. D. Schino, J. M. Kenny. Grain size dependence of the fatigue behaviour of a ultrafine-grained AISI 304 stainless steel ［J］. Mater. Lett., 2003, 57: 3182～3185

[13] [13] L. Zhen, H. Hu, X. Y. Wang et al.. Distribution characterization of boundary misorientation angle of 7050 aluminum alloy after high-temperature compression ［J］. J. Materials Processing Technol., 2009, 209(2): 754～761

[14] [14] Q. Li, Y. B. Xu, Z. H. Lai et al.. Dynamic recrystallization induced by plastic deformation at high strain rate in a Monel alloy ［J］. Materials Science and Engineering A, 2000, 276(1-2): 250～256

[15] [15] I. Mazurina, T. Sakai, H. Miura et al.. Grain refinement in aluminum alloy 2219 during ECAP at 250 ℃ ［J］. Materials Science and Engineering A, 2008, 473: 297～305