[1] [1] MINUS M, KUMAR S. The processing, properties, and structure of carbon fibers［J］. JOM, 2005, 57(2): 52-58.

[2] [2] CHAND S. Review carbon fibers for composites［J］. Journal of Materials Science, 2000, 35(6): 1303-1313.

[3] [3] KIM K W, KIM D K, KIM B S, et al. Cure behaviors and mechanical properties of carbon fiber-reinforced nylon6/epoxy blended matrix composites［J］. Composites Part B: Engineering, 2017, 112: 15-21.

[4] [4] TAM T, BHATNAGAR A. High-performance ballistic fibers and tapes［M］//Lightweight ballistic composites. Amsterdam: Elsevier, 2016: 1-39.

[5] [5] WU J, CHENG X H. Interfacial studies on the surface modified aramid fiber reinforced epoxy composites［J］. Journal of Applied Polymer Science, 2006, 102(5): 4165-4170.

[6] [6] XIE Y X, YANG B B, LU L S, et al. Shear strength of bonded joints of carbon fiber reinforced plastic (CFRP) laminates enhanced by a two-step laser surface treatment［J］. Composite Structures, 2020, 232: 111559.

[7] [7] LI Y Y, MENG S, GONG Q M, et al. Experimental and theoretical investigation of laser pretreatment on strengthening the heterojunction between carbon fiber-reinforced plastic and aluminum alloy［J］. ACS Applied Materials & Interfaces, 2019, 11(24): 22005-22014.

[8] [8] TAO R, ALFANO M, LUBINEAU G. Laser-based surface patterning of composite plates for improved secondary adhesive bonding［J］. Composites Part A: Applied Science and Manufacturing, 2018, 109: 84-94.

[9] [9] WOLYNSKI A, HERRMANN T, MUCHA P, et al. Laser ablation of CFRP using picosecond laser pulses at different wavelengths from UV to IR［J］. Physics Procedia, 2011, 12: 292-301.

[10] [10] GENNA S, LEONE C, UCCIARDELLO N, et al. Increasing adhesive bonding of carbon fiber reinforced thermoplastic matrix by laser surface treatment［J］. Polymer Engineering & Science, 2017, 57(7): 685-692.

[12] [12] LIU Y, ZHANG X, SONG C C, et al. An effective surface modification of carbon fiber for improving the interfacial adhesion of polypropylene composites［J］. Materials & Design, 2015, 88: 810-819.

[14] [14] STEINKE K, GROO L, SODANO H A. Laser induced graphene for in situ ballistic impact damage and delamination detection in aramid fiber reinforced composites［J］. Composites Science and Technology, 2021, 202: 108551.

[15] [15] BAKER A. Bonded composite repair of fatigue-cracked primary aircraft structure［J］. Composite Structures, 1999, 47(1/2/3/4): 431-443.

[16] [16] NURPRASETIO I P, BUDIMAN B A, AZIZ M. Evaluation of bonding strength and fracture criterion for aluminum alloy-woven composite adhesive joint based on cohesive zone model［J］. International Journal of Adhesion and Adhesives, 2018, 85: 193-201.

[17] [17] CHOWDHURY M A, HOSSAIN N, SHUVHO M B A, et al. Improvement of interfacial adhesion performance of the kevlar fiber mat by depositing SiC/TiO2/Al2O3/graphene nanoparticles［J］. Arabian Journal of Chemistry, 2021, 14(11): 103406.

[18] [18] ZHANG B, JIA L H, TIAN M, et al. Surface and interface modification of aramid fiber and its reinforcement for polymer composites: A review［J］. European Polymer Journal, 2021, 147: 110352.

[19] [19] PALOLA S, VUORINEN J, NOORDERMEER J W M, et al. Development in additive methods in aramid fiber surface modification to increase fiber-matrix adhesion: A review［J］. Coatings, 2020, 10(6): 556.

[20] [20] MOHAN J, RAMAMOORTHY A, IVANKOVI A, et al. Effect of an atmospheric pressure plasma treatment on the mode I fracture toughness of a co-cured composite joint［J］. The Journal of Adhesion, 2014, 90(9): 733-754.

[21] [21] SORRENTINO L, POLINI W, BELLINI C, et al. Surface treatment of CFRP: Influence on single lap joint performances［J］. International Journal of Adhesion and Adhesives, 2018, 85: 225-233.

[22] [22] KIM J K, MAI Y W. Interfaces in composites［J］. Materials science and technology, 2006: 257-268.

[23] [23] ZHAN X H, LI Y, GAO C Y, et al. Effect of infrared laser surface treatment on the microstructure and properties of adhesively CFRP bonded joints［J］. Optics & Laser Technology, 2018, 106: 398-409.