[1] Zhan X H, Lin X, Gao Z N et al. Modeling and simulation of the columnar-to-equiaxed transition during laser melting deposition of invar alloy[J]. Journal of Alloys and Compounds, 755, 123-134(2018). http://www.sciencedirect.com/science/article/pii/S0925838818316475

[2] Pu Y S, Wang B Q, Zhang L G. Metal 3D printing technology[J]. Surface Technology, 47, 78-84(2018).

[3] Gong S L[J]. Application of high power beam processing technology in aeroengine Aeronautical Manufacturing Technology, 2013, 34-37.

[4] Wang Y Q, Shen J X, Wu H Q. Application and research status of alternative materials for 3D-printing technology[J]. Journal of Aeronautical Materials, 36, 89-98(2016).

[5] Li S J, Murr L E, Cheng X Y et al. Compression fatigue behavior of Ti-6Al-4V mesh arrays fabricated by electron beam melting[J]. Acta Materialia, 60, 793-802(2012). http://www.sciencedirect.com/science/article/pii/S135964541100766X

[6] Achenbach J D. Quantitative nondestructive evaluation[J]. International Journal of Solids and Structures, 37, 13-27(2000).

[7] Schehl N, Kramb V, Dierken J et al. Ultrasonic assessment of additive manufactured Ti-6Al-4V[C]. AIP Conference Proceedings, 1949, 020008(2018).

[8] Tofeldt O, Pierce S G, Smillie G et al. Investigation of fundamental ultrasonic propagation characteristics in NDT of electron beam melted additive manufactured samples. [C]∥12th European Conference on Non-Destructive Testing, June 11-15, 2018, Gothenburg, Sweden. Scotland, Glasgow: University of Strathclyde(2018).

[9] Sol T, Hayun S, Noiman D et al. Nondestructive ultrasonic evaluation of additively manufactured AlSi10Mg samples[J]. Additive Manufacturing, 22, 700-707(2018). http://www.sciencedirect.com/science/article/pii/S2214860418300484

[10] Gao X Y, Gao X X, Jiang T et al. Defects analysis of large additive manufacturing beam of titanium alloy[J]. Failure Analysis and Prevention, 13, 43-48(2018).

[11] Men P, Dong S Y, Yan S X et al. Influence of heat treatment and measurement methods on material hardness evaluation by longitudinal wave velocity[J]. Journal of Beijing University of Aeronautics and Astronautics, 44, 2312-2320(2018).

[12] Yang P H, Shi L J, Liang J et al[J]. Experimental research on ultrasonic characteristics of TC18 additive manufacturing titanium alloy Aeronautical Manufacturing Technology, 2017, 38-42.

[13] Li X W, Sha A X, Zhang W F et al. TA15 titanium alloy and its applying prospects on airframe[J]. Titanium Industry Progress, 20, 90-94(2003).

[14] Li L Q, Wang J D, Wu C C et al. Temperature field of molten pool and microstructure property in laser melting depositions of Ti6Al4V[J]. Chinese Journal of Lasers, 44, 0302009(2017).

[15] Lai Y B. Research on processing characteristics during laser metal direct desposition additive manufacturing[D]. Shenyang: University of Chinese Academy of Sciences(2015).

[16] Halmshaw R[M]. Introduction to the non-destructive testing of welded joints(1996).

[17] Hislop J D. Flaw size evaluation in immersed ultrasonic testing[J]. Non-Destructive Testing, 2, 183-192(1969). http://www.sciencedirect.com/science/article/pii/0029102169901108

[18] Kleinert W. Defect sizing using non-destructive ultrasonic testing[M]. Cham: Springer(2016).

[19] Zheng H, Lin S Q[M]. Ultrasonic testing, 20-25(2008).

[20] Kirka M M, Greeley D A, Hawkins C et al. Effect of anisotropy and texture on the low cycle fatigue behavior of Inconel 718 processed via electron beam melting[J]. International Journal of Fatigue, 105, 235-243(2017).

[21] Tilita G A, Chen W. Kwan C C F, et al. The effect of ultrasonic excitation on the microstructure of selective laser melted 304L stainless steel[J]. Materialwissenschaft Und Werkstofftechnik, 48, 342-348(2017). http://onlinelibrary.wiley.com/doi/10.1002/mawe.201600763/full

[22] He B B. Characterizing of polymer morphologies & in situ monitoring of injection molding process using ultrasonic techniques[D]. Chengdu: Sichuan University(2006).

[23] Felice M V, Fan Z. Sizing of flaws using ultrasonic bulk wave testing: a review[J]. Ultrasonics, 88, 26-42(2018). http://www.ncbi.nlm.nih.gov/pubmed/29550508

[24] Wang K, Bao R, Liu D et al. Plastic anisotropy of laser melting deposited Ti-5Al-5Mo-5V-1Cr-1Fe titanium alloy[J]. Materials Science and Engineering: A, 746, 276-289(2019).

[25] Kruth J P. Vandenbroucke B, van Vaerenbergh J, et al. Rapid manufacturing of dental prostheses by means of selective laser sintering/melting. [C]∥Les 11ièmes Assises Européennes du Prototypage Rapide, October 4-5, 2005, Paris, France. [S.l.: s.n.](2005).

[26] Wang L, Pratt P, Felicelli S D et al. Pore formation in laser-assisted powder deposition process[J]. Journal of Manufacturing Science and Engineering, 131, 051008(2009).

[27] Susan D F, Puskar J D, Brooks J A et al. Quantitative characterization of porosity in stainless steel LENS powders and deposits[J]. Materials Characterization, 57, 36-43(2006). http://www.sciencedirect.com/science/article/pii/S1044580305002755

[28] Ahsan M N, Bradley R, Pinkerton A J. Microcomputed tomography analysis of intralayer porosity generation in laser direct metal deposition and its causes[J]. Journal of Laser Applications, 23, 022009(2011). http://scitation.aip.org/content/lia/journal/jla/23/2/10.2351/1.3582311

[29] Qiu C L, Panwisawas C, Ward M et al. On the role of melt flow into the surface structure and porosity development during selective laser melting[J]. Acta Materialia, 96, 72-79(2015). http://www.sciencedirect.com/science/article/pii/S1359645415003870