Integrated terahertz (THz) devices are capable of improving system performance in security imaging, high-speed communication, molecular spectroscopy, and other applications^[1,2]. Various THz circuits including conventional microstrip lines^[3], coplanar waveguides^[4,5], substrate-integrated image guides (SIIGs)^[6,7], and spoof surface plasmon polariton (SSPP) waveguides^[8–13] have been reported. Metallic waveguides suffer from high ohmic losses at the THz band^[14–18]. They are costly and difficult to fabricate. Thus, the all-dielectric chips are preferred. As the all-dielectric chips are based on guided-wave optics, they are reasonably efficient. However, it is not possible to independently operate the THz dielectric functional circuits due to the difficulties in the on-chip generation and detection of THz radiation. Usually, the dielectric functional circuits are connected to the conventional THz rectangular metallic waveguides or antennas. Hence, it is necessary to develop the THz couplers with high efficiency. Recently, different types of THz couplers have been reported, including inverse-taper waveguides^[19], Luneburg lenses^[20], and directly coupled couplers^[21]. All of these couplers work on the principle of coupling the THz wave through the chip facet in-plane. However, out-of-plane couplers can be used directly to inject and extract THz waves at arbitrary locations on the chip, which is very important for on-wafer testing. A promising approach is to couple the light to (or from) a chip via a diffraction grating with a spot-size converter formed on the chip surface. This technique is widely used in the optical domain^[22–26]. Interestingly, the diffraction grating structures have good beam steering properties^[27,28]. However, this coupler will be very large in size in the THz frequency range, probably more than 10 cm in length, due to the large wavelength of the THz wave. Thus, it will be difficult to integrate the coupler with other THz functional devices on a single wafer.

In this paper, an out-of-plane coupler for coupling the THz antenna and planar dielectric waveguide is proposed. The coupler consists of a uniform grating and a compact spot-size converter. The THz antenna used is a standard horn antenna. The antenna length is 26.314 mm, and the aperture size is 9.55mm×12.548mm. To match the incident-beam size, the coupling grating is fabricated on a high-resistivity silicon wafer having the dimension of 1 cm wide and 1 cm long. A THz single-mode silicon waveguide is ∼500µm wide^[21]. Hence, a spot-size conversion for 1 cm and 500 µm wide waveguides is required. However, due to the large wavelength of the THz wave, the traditional taper waveguide is too long to be integrated on a wafer. Spot-size converters with lenses that are compact and efficient to focus the guide mode in the dielectric waveguide have been analyzed theoretically^[29]. In this work, we have experimentally verified the concept by employing it in our coupler design at the THz band. The converter is smaller than one-tenth of the traditional taper. The total length of the coupler is 2.9 cm, which results in simpler fabrication on a single silicon wafer. The coupling loss has been found to be ∼5dB at 194 GHz. We also demonstrate the fan-beam steering application of the devices. The steering range of the beam radiated from the grating in the frequency range of 170 GHz to 220 GHz is about 40°. The device is fabricated using a single lithography step on a silicon wafer, which is simple and low cost.

Figure 1(a) shows the schematic of the device fabricated on a silicon wafer. The wafer is 470 µm thick and etched with a depth of 340 µm. The device consists of two couplers connected by a ridge waveguide. A 500 µm wide ridge waveguide is designed to achieve single-mode operation, which is usually used in integrated devices. Each coupler is formed by a grating and a compact spot-size converter with the lens. One grating couples the THz wave radiated from a horn antenna into a multi-mode waveguide. The spot-size converter is used to couple the input wave from the multi-mode waveguide to the single-mode waveguide. Another coupler couples the THz wave back to another horn antenna. As we introduce a lens into the spot-size converter, the length of the taper reduces significantly. Figure 1(b) shows the illustration of the spot-size converter with the lens. The filling factor of each unit can be adjusted to form a waveguide lens and focus the input THz wave. This coupler can be used as the fan-beam steering device, as shown in Fig. 1(c). The THz wave is driven from the ridge-shaped waveguide and radiated into free space through the grating structure, and the resulting beam is controlled by frequency scanning.

We first designed the uniform grating, and the principle of the Bragg grating can be expressed as^[30]Λ=mλ0neff−sinθ,m=0,±1,±2…,(1)where Λ is the period of the grating, m is the diffractive order, and neff and θ are the effective refractive index and the angle of incidence, respectively. Following Eq. (1), we can calculate theoretical grating parameters for the center frequency of 187 GHz. Then, we optimized the grating structure based on finite-difference time-domain (FDTD) solutions from Lumerical using a Gaussian source with a waist radius of 3.5 mm and an incident angle of 9°. The optimal parameters in the inset of Fig. 2(a) are as follows: grating period (Λ) is 0.96 mm, duty cycle (d/Λ) is 0.5, and grating width L1 is 1 cm. The number of grating periods is 10. The total grating area is about 1cm×1cm. As shown in Fig. 2(a), the coupling efficiency at 187 GHz is −4.65dB, and the 3 dB bandwidth is 8.5 GHz. This coupling efficiency is obtained by calculating 10log(Pout/Pin) in the simulation, where Pin is the output power of the Gaussian source, and Pout is the useful power coupling into the waveguide through the grating. According to Eq. (1), the central frequency for different grating parameters can be estimated. However, in order to observe the results more accurately, we also simulate the coupling efficiency for different duty cycles and etching depths. It may be observed from Fig. 2(b) that the central frequency shifts toward a lower frequency, as the duty cycle was increased from 0.4 to 0.6. We can see some sawtooth in it, and this is because of the large scanning step. The scanning step of the duty cycle is 0.02. Figure 2(c) shows that the central frequency shifts to the higher frequency as the etching depth increases. Because the etching depth is not changed in a large range, the maximum coupling efficiency is not greatly affected.

To reduce the length of the device, we designed a compact and efficient spot-size converter with the lens. The purpose of using the lens is to change the effective refractive index of the structure for phase compensation so that the input THz wave could be focused on the spot-size converter. As shown in Fig. 1(b), the lens consists of a periodic silicon block and air slits. Each unit has uniform period (T) and lens thickness (D) but different air slit width (W). According to the Fermat principle and effective index method (EIM), the effective index of each unit is approximately determined as follows: nthickD+nthickF=nmD+nthickM,(2)where nthick is the effective refractive index of the 470 µm planar waveguide, nm is the effective refractive index of the mth unit, which can be seen in Fig. 1(b), F is the distance from the central unit to the focus, and M is the distance from the mth unit to the focus. For all of the units, the light path from the incident light to the focus is equal. The effective refractive index of units can be tuned by the air slit width and approximately calculated by nm=fmnthin2+(1−fm)nthick2,(3)where fm is the filling factor of the mth unit, which is determined by the ratio of slit width (W) to period (T). The effective refractive index of the 130 µm planar waveguide is nthin.

Following Eqs. (2) and (3), we calculated the approximate filling factors of 31 units, as shown by the blue curve in Fig. 3(a). The period (T) and thickness (D) of the lens were 0.3 mm and 1.4 mm, respectively. The focal length (F) was 10 mm. We performed a numerical simulation to optimize the filling factors of units and the length of the tapered waveguide at 187 GHz. Since the tapered waveguide was employed in the converter, the variation gradient of the filling factor is slightly different from the calculation result, which is shown by the red dots in Fig. 3(a). The conversion efficiency reaches a maximum of −0.3dB when the taper is 10 mm long, as shown by the blue curve in Fig. 3(b). This conversion efficiency is obtained by calculating 10log(Plens_out/Plens_in), where Plens_in is the input power of the lens, and Plens_out is the output power of the lens. To compare with our device, we also simulated a traditional adiabatic tapered waveguide, as shown by the red curve in Fig. 3(b). The conversion efficiency increases with the taper length. To achieve the same conversion efficiency as our device, the taper length needs to be around 10 cm, which is too long to be integrated on a wafer.

Then, we simulated the whole structure, including two designed couplers connected by a 6 cm long waveguide. Figure 3(c) shows that the coupling efficiency of the whole structure can reach −9.2dB at 192.857 GHz. The 3 dB coupling bandwidth is about 14 GHz. The normalized optical power distribution of the device with the lens is shown in Fig. 3(d). Figures 3(e) and 3(f) show the input and output optical field distributions of the spot-size converter, respectively. The optical mode is found to be well concentrated into the signal mode waveguide, and the size of the optical mode is significantly reduced to ∼0.5mm. The simulation results show that the structure size can be reduced after adding the slit silicon lens.

The device was fabricated on a 6 inch (1 inch = 2.54 cm) high-resistivity wafer, which is 470 µm thick and double-sided polished. The dielectric constant is 11.7, and the resistivity is more than 5 kΩ·cm. The wafer is etched with a depth of 340 µm to form ridge waveguides by the deep reactive ion etching (DRIE) process. The optical image of the device with the lens is shown in Fig. 4(a). There are two compact couplers, and the length of the connecting waveguide between them is 6 cm. Figure 4(b) shows the optical image of the traditional coupler without a lens. The coupler structure is 11.9 cm long, which is obviously hard to integrate with other THz devices on a 6 inch wafer. Figure 4(c) shows the experimental setup for coupling measurement.

We used an Agilent N5227A PNA network analyzer, a set of WR-5.1 140–220 GHz expanders, and a pair of WR-5.1 horn antennas to characterize the coupling performance of the device. After the calibration, the horn antennas were connected to hollow metallic waveguide ports. Then, we used the four-axis alignment stage to adjust the coupling angle and the distance between horn antennas and gratings. The connected waveguide is 6 cm long, and the transmission loss of the waveguide in the TM mode was about 0.054 dB/cm^[21]. Therefore, the loss of the connected waveguide is negligible. Notably, the loss of two antennas should be taken into consideration because it could reach about 9 dB. Under this situation, we normalized the test results, and the measured normalized coupling efficiency of the device using couplers with the lens is shown in Fig. 4(d) by the red curve. It is observed that the maximal transmission reaches −10dB. The coupling efficiency of one coupler proposed in this paper is around −5dB. Compared with the simulation results, the center frequency is shifted to 194 GHz, and the 3 dB bandwidth is reduced to 2.5 GHz. We also measured the coupling efficiency of the coupler without a lens, as shown in Fig. 4(d) by the blue curve. Due to the long spot-size converter and connected waveguide, the maximal coupling efficiency of this coupler could only reach −6.5dB. The results indicate that our device is extremely compact and has a lower loss. The coupling efficiency of our coupler is close to that of the uniform grating devices in optical bands^[31], and special designs can be used to improve the coupling efficiency in the future^[32]. Table 1 lists the comparison of our device with various reported THz couplers including inverse-taper waveguides, Luneburg lenses, and directly coupled couplers. The main advantage of our work is that it provides an out-of-plane coupling in the THz band.

Finally, we demonstrated the fan-beam steering application of the grating. The illustration of the beam steering application has been shown in Fig. 1(c). According to Eq. (1), the angle of the diffraction light beam (θ) will increase with the frequency. Numerical simulation results show that within the frequency range of 170–220 GHz, the steering range of the near-field beam can reach ∼40° in the θ direction, as shown in Fig. 5(a). Figure 5(b) shows the experimental setup. The THz wave is coupled end-to-end into the ridge-shaped silicon waveguide, and a rectangular waveguide probe is used as a receiver to obtain the electric field distribution of the beam radiated from the grating. The distance between the probe and the grating is 5 mm, and the x–y plane scan range is 2cm×2cm, which resulted in 39×39 pixels. As shown in Fig. 5(c), the experimental fan-beam steering range is around 40° in the frequency range of 170–220 GHz. We show the normalized beam profiles of the electric field distributions of 180 GHz, 190 GHz, and 200 GHz in Figs. 5(d), 5(e), and 5(f), respectively. It can be seen that the electric field is mainly distributed at y=1.2cm, i.e., right in the middle of the grating. The radiated beam moves to the right along the x axis as the frequency increases, i.e., the steering angle increases. Note that the electric field steering distribution in Fig. 5(c) was extracted from the electric field of each beam of a different frequency at y=1.2cm. Thus, THz beam steering application could be obtained using the device.

In this paper, we proposed and demonstrated a THz out-of-plane coupler with a compact spot-size converter. The total length of the device is 2.9 cm, which is much shorter than the coupler with a traditional spot-size converter. Experimental results show that the coupling efficiency is ∼5dB at 194 GHz, and the beam steering range is about 40° from 170 GHz to 220 GHz. Therefore, the devices provide out-of-plane coupling and fan-beam steering of THz dielectric chips. We believe that the proposed structure will contribute to the development of THz integrated devices, especially silicon-based devices.