[1] [1] Yan K, Zhang J H, Hong J, Wang Y T and Zhu Y S 2016 Structural optimization of lubrication device for high speed angular contact ball bearing based on internal fluid flow analysis Int. J. Heat Transfer 95 540–50

[2] [2] Cui H L, Zhao Y and Dong W C 2021 Research on life prediction method of rolling bearing based on deep learning and voice interaction technology Int. J. Speech Technol. (https://doi.org/10.1007/s10772-021-09873-5)

[3] [3] Lin J R 2000 Surface roughness effect on the dynamic stiffness and damping characteristics of compensated hydrostatic thrust bearings Int. J. Mach. Tools Manuf.40 1671–89

[4] [4] Wang Y, Tong H, Sima H, Wang J Y, Sun J J and Huang D G2019 Experimental study on aerodynamic performance of deformable blade for vertical axis wind turbine Energy181 187–201

[5] [5] Sharma S C and Singh A 2023 A study of double layer conical porous hybrid journal bearing operated with non-Newtonian lubricant Tribol. Int. 179 108183

[6] [6] Sadabadi H and Nezhad A S 2020 Nanofluids for performance improvement of heavy machinery journal bearings: a simulation study Nanomaterials 10 2120

[7] [7] Du J L and Liang G Z 2019 Performance comparative analysis of hydrostatic bearings lubricated with low-viscosity cryogenic fluids Tribol. Int. 137 139–51

[8] [8] Zhang W M, Zhou J B and Meng G 2011 Performance and stability analysis of gas-lubricated journal bearings in MEMS Tribol. Int. 44 887–97

[9] [9] Kumar C and Sarangi S 2022 Dynamic behavior of self-acting gas-lubricated long journal bearing Mech. Res.Commun. 124 103950

[10] [10] Sharma S C, Phalle V M and Jian S C 2011 Performance analysis of a multirecess capillary compensated conical hydrostatic journal bearing Tribol. Int. 44 617–26

[11] [11] Qiang M C, Zhao Q, Yan S H, Liu X, Hou Y and Lai T W 2022 Performance prediction of high-speed hydrogen gas-lubricated herringbone grooved journal bearing Appl.Sci. 12 6432

[12] [12] Yabe H and Ishida H 1991 A study on the running accuracy of an externally pressurized gas thrust bearing: rotor run-out characteristics JSME Int. J. III 34 333–8

[13] [13] Zhang P H, Chen Y L and Zha J 2017 Relationship between geometric errors of thrust plates and error motions of hydrostatic thrust bearings under quasi-static condition Precis. Eng. 50 119–31

[14] [14] Zoupas L, Wodtke M, Papadopoulos C I and Wasilczuk M 2019 Effect of manufacturing errors of the pad sliding surface on the performance of the hydrodynamic thrust bearing Tribol. Int. 134 211–20

[15] [15] Cui H L, Wang Y, Yue X B, Huang M and Wang W 2017 Effects of manufacturing errors on the static characteristics of aerostatic journal bearings with porous restrictor Tribol. Int. 115 246–60

[16] [16] Kim K M and Kim K W 1992 An analytical study on the rotational accuracy of externally pressurized air journal bearing JSME Int. J. III 35 485–92

[17] [17] Yabe H 1994 A study on run-out characteristics of externally pressurized gas journal bearing: rotor run-out characteristics JSME Int. J. C 37 355–61

[18] [18] Zhang P H 2020 A study on accuracy of porous journal air bearing Precis. Eng. 66 42–51

[19] [19] Wang H W, Xiang J W, Zhao X F and Li Y L 2023 A kinematic precision reliability evaluation method for rotor-bearing systems considering multi-source wear degradations and random errors Int. J. Adv. Manuf.Technol. 124 4159–73

[20] [20] Cappa S, Reynaerts D and Al-Bender F 2014 Reducing the radial error motion of an aerostatic journal bearing to a nanometre level: theoretical modelling Tribol. Lett.53 27–41

[21] [21] Martin D L, Tabenkin A N and Parsons F G 1995 Precision spindle and bearing error analysis Int. J. Mach. Tools Manuf. 35 187–93

[22] [22] Lou M Y, Bareille O, Chai W Q, Ichchou M and Chen W 2020 Global sensitivity analysis of static characteristics of tilting-pad journal bearing to manufacturing tolerances Tribol. Int. 149 105734

[23] [23] Khim G, Oh J S and Park C H 2014 Analysis of 5-DOF motion errors influenced by the guide rails of an aerostatic linear motion stage Int. J. Precis. Eng. Manuf. 15 283–90

[24] [24] Aleyaasin M, Whalley R and Ebrahimi M 2000 Error correction in hydrostatic spindles by optimal bearing tuning Int. J. Mach. Tools Manuf. 40 809–22

[25] [25] Ro S K, Kim S, Kwak Y and Park C H 2010 A linear air bearing stage with active magnetic preloads for ultraprecise straight motion Precis. Eng. 34 186–94

[26] [26] Zhang P H and Zha J 2021 Dynamic accuracy model of porous journal air bearing considering rotational speed Tribol. Int. 161 107064

[27] [27] Zhang P H 2021 Accuracy prediction model of an orifice-compensated aerostatic bearing Precis. Eng.72 837–46

[28] [28] Yin T F, To S, Du H H and Zhang G Q 2022 Effects of wheel spindle error motion on surface generation in grinding Int.J. Mech. Sci. 218 107046

[29] [29] Lu Z W, Zhang J N and Liu B 2021 Research on the fluctuation of the velocity and pressure of the flow field of an aerostatic bearing with a multi-hole integrated restrictor Proc. Inst. Mech. Eng. J 235 2007–20

[30] [30] Dal A and Kara?ay T 2021 Pneumatic hammer instability in the aerostatic journal bearing-rotor system: a theoretical and experimental analyses Proc. Inst. Mech. Eng. J 235 524–43

[31] [31] Kodnyanko V, Shatokhin S, Kurzakov A and Pikalov Y 2021 Theoretical analysis of compliance and dynamics quality of a lightly loaded aerostatic journal bearing with elastic orifices Precis. Eng. 68 72–81

[32] [32] Ye Y X, Chen X D, Hu Y T and Luo X 2010 Effects of recess shapes on pneumatic hammering in aerostatic bearings Proc. Inst. Mech. Eng. J 224 231–7

[33] [33] Cui H L, Gong W W, Zheng Y Q, Li Y F, Wang W and Jiang Z Y 2021 A simplified FEM analysis on the static performance of aerostatic journal bearings with orifice restrictor Proc. Inst. Mech. Eng. J 235 1379–89

[34] [34] Huang M, Cui H L, Liu P K, Li M Y, Zheng Y Q and Jiang Z Y 2019 A theoretical and experimental study on the stiffness of aerostatic thrust bearings with vacuum preloading Proc. Inst. Mech. Eng. J 233 256–70

[35] [35] Branch H D, Watkins C B and Eronini I E 1984 Vibration of a hydrostatic gas bearing due to supply pressure oscillations Wear 95 199–212

[36] [36] Chen Y S, Chiu C C and Cheng Y D 2010 Influences of operational conditions and geometric parameters on the stiffness of aerostatic journal bearings Precis. Eng.34 722–34

[37] [37] Zhang J B, Han D J, Song M B, Xie Z L, Rao Z S and Zou D L 2021 Theoretical and experimental investigation on the effect of supply pressure on the nonlinear behaviors of the aerostatic bearing-rotor system Mech. Syst. Signal Process. 158 107775

[38] [38] Chen X D and He X M 2006 The effect of the recess shape on performance analysis of the gas-lubricated bearing in optical lithography Tribol. Int. 39 1336–41

[39] [39] Tomar A K and Sharma S C 2022 Non-Newtonian lubrication of hybrid multi-recess spherical journal bearings with different geometric shapes of recess Tribol.Int. 171 107579

[40] [40] Hashimoto H and Namba T 2009 Optimization of groove geometry for a thrust air bearing according to various objective functions J. Tribol. 131 041704

[41] [41] Du J J, Zhang G Q, Liu T and To S 2014 Improvement on load performance of externally pressurized gas journal bearings by opening pressure-equalizing grooves Tribol.Int. 73 156–66

[42] [42] Wu H, Huang Y, Cui H L and Rong Y M 2021 A passive compensated method with hydraulic transmission for static infinite stiffness of thrust bearing Tribol. Int. 163 107193

[43] [43] Belforte G, Colombo F, Raparelli T, Trivella A and Viktorov V 2013 Experimental analysis of air pads with micro holes Tribol. Trans. 56 169–77

[44] [44] Miyatake M and Yoshimoto S 2010 Numerical investigation of static and dynamic characteristics of aerostatic thrust bearings with small feed holes Tribol. Int. 43 1353–9

[45] [45] Fan K C, Ho C C and Mou J I 2002 Development of a multiple-microhole aerostatic air bearing system J.Micromech. Microeng. 12 636–43

[46] [46] He X M, Chen X D, Zeng L Z and Yu X Z 2008 Analysis of the positioning accuracy of ultra-precision stage with air-thrust bearings J. Huazhong Univ. Sci. Technol. 36 8–11

[47] [47] Gao Q, Chen W Q, Lu L H, Huo D H and Cheng K 2019 Aerostatic bearings design and analysis with the application to precision engineering: state-of-the-art and future perspectives Tribol. Int. 135 1–17

[48] [48] Khatri C B and Sharma S C 2018 Analysis of textured multi-lobe non-recessed hybrid journal bearings with various restrictors Int. J. Mech. Sci. 145 258–86

[49] [49] Otsu Y, Somaya K and Yoshimoto S 2011 High-speed stability of a rigid rotor supported by aerostatic journal bearings with compound restrictors Tribol. Int. 44 9–17

[50] [50] Zheng Y Q, Yang G W, Cui H L and Hou Y 2020 Improving the stiffness of the aerostatic thrust bearing by using a restrictor with multi-orifice series Proc. Inst. Mech. Eng. J 234 1881–91

[51] [51] Sun N, Yang C, Song J F, Li Y T, Yang W B, Zhou Y L,Luo D L and Zhang Q P 2023 Tailoring thermal resistance of porous materials with void filling for improved hydrogen adsorption Int. J. Hydrog. Energy 48 8588–95

[52] [52] Singh A and Sharma S C 2022 Behaviour of conical porous hybrid journal bearing operated with MHD lubricant considering influence of surface irregularities Tribol. Int.174 107730

[53] [53] Cui H L, Wang Y, Zhang M, Wang W and Zhao C J 2018 A fractal method to calculate the permeability for compressible gas flow through a porous restrictor in aerostatic bearings Int. J. Heat Mass Transfer 121 437–52

[54] [54] Wang W, Cheng X H, Zhang M, Gong W W and Cui H L 2020 Effect of the deformation of porous materials on the performance of aerostatic bearings by fluid-solid interaction method Tribol. Int. 150 106391

[55] [55] Zeng C Q, Wang W, Cheng X H, Zhao R and Cui H L 2021 Three-dimensional flow state analysis of microstructures of porous graphite restrictor in aerostatic bearings Tribol.Int. 159 106955

[56] [56] Horikawa O and Shimokohbe A 1990 An active air bearing:control of radial axis motion and stiffness JSME Int. J. III33 55–60

[57] [57] Al-Bender F 2009 On the modelling of the dynamic characteristics of aerostatic bearing films: from stability analysis to active compensation Precis. Eng. 33 117–26

[58] [58] Maamari N, Krebs A, Weikert S and Wegener K 2019 Centrally fed orifice based active aerostatic bearing with quasi-infinite static stiffness and high servo compliance Tribol. Int. 129 297–313

[59] [59] Al-Bender F and Brussel H V 1997 Active aerostatic bearing through control of film geometry Proc. 9th Int. Precision Engineering pp 389–92

[60] [60] Luo X H, Han B, Chen X D, Li X P and Jiang W 2021 Multi-physics modeling of tunable aerostatic bearing with air gap shape compensation Tribol. Int. 153 106587

[61] [61] Santos I F, Nicoletti R and Scalabrin A 2004 Feasibility of applying active lubrication to reduce vibration in industrial compressors J. Eng. Gas Turbines Power 126 848–54

[62] [62] Park C H, Oh Y J, Shamoto E and Lee D W 2006 Compensation for five DOF motion errors of hydrostatic feed table by utilizing actively controlled capillaries Precis. Eng. 30 299–305

[63] [63] Morosi S and Santos I F 2011 Active lubrication applied to radial gas journal bearings. Part I: modeling Tribol. Int.44 1949–58

[64] [64] Pierart F G and Santos I F 2016 Active lubrication applied to radial gas journal bearings. Part 2: modelling improvement and experimental validation Tribol. Int. 96 237–46

[65] [65] Feng K, Shi M H, Gong T, Liu Y Y and Zhu J 2017 A novel squeeze-film air bearing with flexure pivot-tilting pads:numerical analysis and measurement Int. J. Mech. Sci.134 41–50

[66] [66] Colombo F, Lentini L, Raparelli T, Trivella A and Viktorov V 2021 Design and analysis of an aerostatic pad controlled by a diaphragm valve Lubricants 9 47

[67] [67] Liu Y, Wan M, Xiao Q B and Qin X B 2022 Combined predictive and feedback contour error control with dynamic contour error estimation for industrial five-axis machine tools IEEE Trans. Ind. Electron. 69 6668–77

[68] [68] Du J J, Liu D, Zhang G Q and Zhu J J 2010 Study of self-excited vibration for externally pressurized gas thrust bearing with circumferential groove Lubr. Eng. 35 9–12

[69] [69] Li Y F, Yin Y H, Yang H, Liu X N, Mo J and Cui H L 2017 Modeling for optimization of circular flat pad aerostatic bearing with a single central orifice-type restrictor based on CFD simulation Tribol. Int. 109 206–16

[70] [70] He D X, Sheng B H, Zhou Z D, Suo Q, Li Y F and Liu C Y 2009 Improvement of diamond-cutting surface by means of porous bearing laminar flow Chin. Mech. Eng.20 1180–3

[71] [71] Kong Z K and Tao J Z 2013 Pneumatic hammer in aerostatic thrust bearings with single orifice compensation Proc.SPIE 8759 20–26

[72] [72] Zheng Y Q, Yang G W, Cui H L and Hou Y 2020 Pneumatic stability analysis of single-pad aerostatic thrust bearing with pocketed orifice Proc. Inst. Mech. Eng. J234 1857–66

[73] [73] Aoyama T, Kakinuma Y and Kobayashi Y 2006 Numerical and experimental analysis for the small vibration of aerostatic guideways CIRP Ann. 55 419–22

[74] [74] Eleshaky M E 2009 CFD investigation of pressure depressions in aerostatic circular thrust bearings Tribol.Int. 42 1108–17

[75] [75] Feng K, Wang P, Zhang Y J, Hou W J, Li W J, Wang J W and Cui H L 2021 Novel 3D printed aerostatic bearings for the improvement of stability: theoretical predictions and experimental measurements Tribol. Int. 163 107149

[76] [76] Yoshimura T, Hanafusa T, Kitagawa T, Hirayama T,Matsuoka T and Yabe H 2012 Clarifications of the mechanism of nano-fluctuation of aerostatic thrust bearing with surface restriction Tribol. Int. 48 29–34

[77] [77] Li W J, Zhang Y J, Wang P, Feng K, Cui H L and Zheng Y Q2022 Novel full-region model of inherent orifice aerostatic bearings considering air flow in orifice and clearance Lubr.Sci. 34 258–74

[78] [78] Chen X D, Chen H, Luo X, Ye Y X, Hu Y T and Xu J Q 2011 Air vortices and nano-vibration of aerostatic bearings Tribol. Lett. 42 179–83

[79] [79] Talukder H M and Stowell T B 2003 Pneumatic hammer in an externally pressurized orifice-compensated air journal bearing Tribol. Int. 36 585–91

[80] [80] Kong Z K, Tao J Z, Ji F and Xia H 2013 Experimental study on pneumatic hammer of aerostatic bearings with supply holes Lubr. Eng. 38 66–70

[81] [81] Ma W, Cui J W, Liu Y M and Tan J B 2016 Improving the pneumatic hammer stability of aerostatic thrust bearing with recess using damping orifices Tribol. Int.103 281–8

[82] [82] Otsu Y, Miyatake M and Yoshimoto S 2011 Dynamic characteristics of aerostatic porous journal bearings with a surface-restricted layer J. Tribol. 133 011701

[83] [83] Li Y T, Wan X and Li X L 2017 Microvibration suppression of an aerostatic thrust bearing adopting flow field disturbance structure Adv. Mech. Eng. 9 1–9

[84] [84] Yu P L, Lu J, Luo Q, Li G H and Yin X X 2022 Optimization design of aerostatic bearings with square micro-hole arrayed restrictor for the improvement of stability: theoretical predictions and experimental measurements Lubricants 10 295

[85] [85] Cui H L, Wang Y, Wang B R, Yang H and Xia H 2018 Numerical simulation and experimental verification of the stiffness and stability of thrust pad aerostatic bearings Chin. J. Mech. Eng. 31 23

[86] [86] Kawai T, Ebihara K and Takeuchi Y 2005 Improvement of machining accuracy of 5-axis control ultraprecision machining by means of laminarization and mirror surface finishing CIRP Ann. 54 329–32

[87] [87] Tomar A K and Sharma S C 2022 Study on surface roughness and piezo-viscous shear thinning lubricant effects on the performance of hole-entry hybrid spherical journal bearing Tribol. Int. 168 107349

[88] [88] Larsen J S, Santos I F and von Osmanski S 2016 Stability of rigid rotors supported by air foil bearings: comparison of two fundamental approaches J. Sound Vib. 381 179–91

[89] [89] Howard S A 1999 Rotordynamics and design methods of an oil-free turbocharger Tribol. Trans. 42 174–9

[90] [90] Xie W S, Lin X, Wang W T, Shen Q and He Z P 2018 Review of technique application and performance evaluation for aerodynamic elastic foil gas bearing in aero-engine Lubr. Eng. 43 136–47

[91] [91] Hwang S H, Moon C G, Kim T H, Lee J, Cho K S, Ha K K and Lee C H 2019 Rotordynamic performance measurements and predictions of a FCEV air compressor supported on gas foil bearings Tribol. Lubr. 35 44–51

[92] [92] Schiffmann J and Favrat D 2009 Experimental investigation of a direct driven radial compressor for domestic heat pumps Int. J. Refrig. 32 1918–28

[93] [93] Pattnayak M R, Ganai P, Pandey P K, Dutt J K and Fillon M 2022 An overview and assessment on aerodynamic journal bearings with important findings and scope for explorations Tribol. Int. 174 107778

[94] [94] Liu W H, B?ttig P, Wagner P H and Schiffmann J 2021 Nonlinear study on a rigid rotor supported by herringbone grooved gas bearings: theory and validation Mech. Syst.Signal Process. 146 106983

[95] [95] Diehl M, Schreiber C and Schiffmann J 2020 The role of Reynolds number effect and tip leakage in compressor geometry scaling at low turbulent Reynolds numbers J.Turbomach. 142 031003

[96] [96] Liu W H, Gjika K and Schiffmann J 2023 Design and experimental investigation of a herringbone grooved gas bearing supported turbocharger Mech. Syst. Signal Process. 186 109828

[97] [97] Gu L L, Guenat E and Schiffmann J 2020 A review of grooved dynamic gas bearings Appl. Mech. Rev. 72 010802

[98] [98] Li Y Y, Liu J F, Li L L and Yang D S 2018 Effect of environmental pressure on dynamic characteristics of aerodynamic gas bearing of boost turbo expander IOP Conf. Ser.: Mater. Sci. Eng. 382 032018

[99] [99] Bediz B, Gozen B A, Korkmaz E and Ozdoganlar O B 2014Dynamics of ultra-high-speed (UHS) spindles used for micromachining Int. J. Mach. Tools Manuf. 87 27–38

[100] [100] Pattnayak M R, Pandey R K and Dutt J K 2021 Effects of new micro-pocketed bore surface topographies on the performance behaviours of aerodynamic journal bearing Surf. Topography: Metrol. Prop. 9 025001

[101] [101] Yu Y L, Pu G, Jiang T C and Jiang K 2020 A dragonfly wing inspired biomimetic aerodynamic thrust bearing for increased load capacity Int. J. Mech. Sci. 176 105550

[102] [102] Blok H and von Rossum J J 1953 The foil bearing-a new departure in hydrodynamic lubrication Lubr. Eng.9 316–20

[103] [103] Ghalayini I and Bonello P 2022 Nonlinear and linearised analyses of a generic rotor on single-pad foil-air bearings using Galerkin Reduction with different applied air film conditions J. Sound Vib. 525 116774

[104] [104] Guo Z Y, Lyu P, Feng K and Liu W H 2018 Measurement and prediction of nonlinear dynamics of a gas foil bearing supported rigid rotor system Measurement 121 205–17

[105] [105] Xu Z N, Li C L and Du J J 2021 Modeling and static characteristics study of the double-layer bump gas foil bearing Tribol. Int. 164 107202

[106] [106] Heshmat H, Shapiro W and Gray S 1982 Development of foil journal bearings for high load capacity and high speed whirl stability J. Tribol. 104 149–56

[107] [107] Mahne M, Bauer M, Lehn A and Schweizer B 2019 An experimental investigation on the influence of an assembly preload on the hysteresis, the drag torque, the lift-off speed and the thermal behavior of three-pad air foil journal bearings Tribol. Int. 137 113–26

[108] [108] Zhao X W and Xiao S H 2021 A three-dimensional model of gas foil bearings and the effect of misalignment on the static performance of the first and second generation foil bearings Tribol. Int. 156 106821

[109] [109] Lyu P, Feng K, Zhu B H, Zhang K and Sun D L 2019 The performance evaluation of the promising high-stability foil bearings basing with flexure pivot tilting pads Mech. Syst.Signal Process. 134 106313

[110] [110] Ribeiro E A, Alves D S, Cavalca K L and Bavastri C A 2021 Stability analysis and optimization of a hybrid rotating machinery support combining journal bearings with viscoelastic supports Mach. Mech. Theory 156 104166

[111] [111] Feng K, Zhao X Y, Huo C J and Zhang Z M 2016 Analysis of novel hybrid bump-metal mesh foil bearings Tribol. Int.103 529–39

[112] [112] Pham M N and Ahn H J 2014 Experimental optimization of a hybrid foil-magnetic bearing to support a flexible rotor Mech. Syst. Signal Process. 46 361–72

[113] [113] van Osmanski S and Santos I F 2021 Gas foil bearings with radial injection: multi-domain stability analysis and unbalance response J. Sound Vib. 508 116177

[114] [114] Park J, Kim D and Sim K 2021 Rotordynamic analysis of piezoelectric gas foil bearings with a mechanical preload control based on structural parameter identifications Appl. Sci. 11 2330

[115] [115] Feng K, Gao Y L, Yu K, Guan H Q, Wu Y H and Guo Z Y 2019 Characterization of a controllable stiffness foil bearing with shape memory alloy springs Tribol. Int.136 360–71

[116] [116] Guan H Q, Wei K X, Mao W G, He Q B and Zou H X 2023Study on the static and dynamic performance of active bump-metal mesh foil bearings Mech. Syst. Signal Process. 184 109690

[117] [117] Delgado A and Ertas B 2019 Dynamic characterization of a novel externally pressurized compliantly damped gas-lubricated bearing with hermetically sealed squeeze film damper modules J. Eng. Gas Turbines Power141 021028

[118] [118] Sim K, Yong-Bok L, Kim T H and Lee J 2012 Rotordynamic performance of shimmed gas foil bearings for oil-free turbochargers J. Tribol. 134 031102

[119] [119] Sim K, Lee Y B and Kim T H 2013 Effects of mechanical preload and bearing clearance on rotordynamic performance of lobed gas foil bearings for oil-free turbochargers Tribol. Trans. 56 224–35

[120] [120] Kim T H and Andrés L S 2009 Effects of a mechanical preload on the dynamic force response of gas foil bearings: measurements and model predictions Tribol. Trans. 52 569–80

[121] [121] Hoffmann R and Liebich R 2017 Experimental and numerical analysis of the dynamic behaviour of a foil bearing structure affected by metal shims Tribol. Int.115 378–88

[122] [122] Zhou Q, Hou Y and Chen C Z 2009 Dynamic stability experiments of compliant foil thrust bearing with viscoelastic support Tribol. Int. 42 662–5

[123] [123] Feng K, Liu Y M, Zhao X Y and Liu W H 2016 Experimental evaluation of the structure characterization of a novel hybrid bump-metal mesh foil bearing J. Tribol. 138 021702

[124] [124] Lee Y B, Kim T H, Kim C H, Lee N S and Choi D H 2004 Dynamic characteristics of a flexible rotor system supported by a viscoelastic foil bearing (VEFB) Tribol. Int. 37 679–87

[125] [125] Andrés L S and Chirathadam T A 2013 Performance characteristics of metal mesh foil bearings: predictions versus measurements J. Eng. Gas Turbines Power135 122503

[126] [126] Silva H A P and Nicoletti R 2023 Rotor vibration control using tilting-pad journal bearing with active pads-numerical and experimental results J. Sound Vib.546 117441

[127] [127] Shrestha S K, Kim D and Kim Y C 2013 Experimental feasibility study of radial injection cooling of three-pad air foil bearings J. Tribol. 135 041703

[128] [128] Yazdi B Z and Kim D 2018 Rotordynamic performance of hybrid air foil bearings with regulated hydrostatic injection J. Eng. Gas Turbines Power 140 012506

[129] [129] Park J and Sim K 2019 A feasibility study of controllable gas foil bearings with piezoelectric materials via rotordynamic model predictions J. Eng. Gas Turbines Power 141 021027

[130] [130] Kumar V and Sharma S C 2017 Combined influence of couple stress lubricant, recess geometry and method of compensation on the performance of hydrostatic circular thrust pad bearing Proc. Inst. Mech. Eng. J 231 716–33

[131] [131] Xiong W L, Hu C, Lü L and Zheng L G 2018 Research on the influence of controllable restrictor parameters on the characteristics of hydrostatic journal bearings J. Mech.Eng. 54 63–71

[132] [132] Gao S, Chatterton S, Naldi L and Pennacchi P 2021 Ball bearing skidding and over-skidding in large-scale angular contact ball bearings: nonlinear dynamic model with thermal effects and experimental results Mech. Syst.Signal Process. 147 107120

[133] [133] Michalec M, Svoboda P, Kˇrupka I and Hartl M 2021 A review of the design and optimization of large-scale hydrostatic bearing systems Int. J. Eng. Sci. Technol. 24 936–58

[134] [134] Yuan J L, Zhang F H, Dai Y F, Kang R K, Yang H and Lü B H 2010 Development research of science and technologies in ultra-precision machining field J. Mech. Eng. 46 161–77

[135] [135] Sharma S C, Jain S C and Bharuka D K 2002 Influence of recess shape on the performance of a capillary compensated circular thrust pad hydrostatic bearing Tribol. Int. 35 347–56

[136] [136] Singh N, Sharma S C, Jain S C and Reddy S S 2004 Performance of membrane compensated multirecess hydrostatic/hybrid flexible journal bearing system considering various recess shapes Tribol. Int. 37 11–24

[137] [137] Gao S Y, Cheng K, Chen S J, Ding H and Fu H Y 2015 CFD based investigation on influence of orifice chamber shapes for the design of aerostatic thrust bearings at ultra-high speed spindles Tribol. Int. 92 211–21

[138] [138] Bassani R and Piccigallo B 1992 Hydrostatic Lubrication(Elsevier)

[139] [139] Bakker O J and van Ostayen R A J 2010 Recess depth optimization for rotating, annular, and circular recess hydrostatic thrust bearings J. Tribol. 132 011103

[140] [140] Shao J P, Liu G D, Yu X D, Zhang Y Q, Meng X L and Jiang H 2018 Effect of recess depth on lubrication performance of annular recess hydrostatic thrust bearing by constant rate flow Ind. Lubr. Tribol. 70 68–75

[141] [141] Kang Y, Chen C H, Lee H H, Hung Y H and Hsiao S T 2011Design for static stiffness of hydrostatic bearings:single-action variable compensations Ind. Lubr. Tribol.63 103–18

[142] [142] Lai T H, Chang T Y, Yang Y L and Lin S C 2017 Parameters design of a membrane-type restrictor with single-pad hydrostatic bearing to achieve high static stiffness Tribol.Int. 107 206–12

[143] [143] Hanawa N, Kuniyoshi M, Miyatake M and Yoshimoto S 2017 Static characteristics of a water-lubricated hydrostatic thrust bearing with a porous land region and a capillary restrictor Precis. Eng. 50 293–307

[144] [144] Santos I F and Watanabe F Y 2006 Lateral dynamics and stability analysis of a gas compressor supported by hybrid and active lubricated multirecess journal bearing J. Braz.Soc. Mech. Sci. Eng. 28 485–95

[145] [145] Nicoletti R and Santos I F 2008 Control system design for flexible rotors supported by actively lubricated bearings J.Vib. Control 14 347–74

[146] [146] Estupi?nan E A and Santos I F 2009 Linking rigid multibody systems via controllable thin fluid films Tribol. Int.42 1478–86

[147] [147] Rehman W U R, Luo Y X, Wang Y Q, Jiang G Y, Iqbal N,Rehman S U R and Bibi S 2019 Fuzzy logic-based intelligent control for hydrostatic journal bearing Meas.Control 52 229–43

[148] [148] Rehman W U, Wang X H, Cheng Y Q, Chen Y C,Shahzad H, Chai H, Abbas K, Ullah Z and Kanwal M 2021 Model-based design approach to improve performance characteristics of hydrostatic bearing using multivariable optimization Mathematics 9 388

[149] [149] Kumar M, Kumar A, Bharti R K, Yadav H N S and Das M 2022 A review on rheological properties of magnetorheological fluid for engineering components polishing Mater. Today Proc. 56 A6–A12

[150] [150] Lampaert S G E, Quinci F and van Ostayen R A J 2020 Rheological texture in a journal bearing with magnetorheological fluids J. Magn. Magn. Mater.499 166218

[151] [151] Peng J and Zhu K Q 2005 Hydrodynamic characteristics of ER journal bearings with external electric field imposed on the contractive part J. Intell. Mater. Syst. Struct. 16 493–9

[152] [152] Sharma S C and Khatri C B 2018 Electro-rheological fluid lubricated textured multi-lobe hole-entry hybrid journal bearing system J. Intell. Mater. Syst. Struct. 29 1600–19

[153] [153] Uhlmann E, Spur G, Bayat N and Patzwald R 2002 Application of magnetic fluids in tribotechnical systems J.Magn. Magn. Mater. 252 336–40

[154] [154] Eshgarf H, Nadooshan A A and Raisi A 2022 An overview on properties and applications of magnetorheological fluids: dampers, batteries, valves and brakes J. Energy Storage 50 104648

[155] [155] Sahu K, Sharma S C and Ram N 2022 Misalignment and surface irregularities effect in MR fluid journal bearing Int. J. Mech. Sci. 221 107196

[156] [156] Zapomeˇl J and Ferfecki P 2022 A new concept of a hydrodynamic bearing lubricated by composite magnetic fluid for controlling the bearing load capacity Mech. Syst.Signal Process. 168 108678

[157] [157] Varnusfaderani M A, Parizi M I, Hemmatian M and Ohadi A 2022 Experimental parameters identification of a flexible rotor system equipped with smart magneto-rheological bearing Mechatronics 87 102880

[158] [158] Kuzhir P P, Kuzhir P G, Gul’kov G I and Rudenya A L 2011 Determination of the free boundary of the lubricant layer of a ferrofluid bearing J. Eng. Phys. Thermophys. 84 422–9

[159] [159] Hsu T C, Chen J H, Chiang H L and Chou T L 2013 Lubrication performance of short journal bearings considering the effects of surface roughness and magnetic field Tribol. Int. 61 169–75

[160] [160] Bin Mazlan S A 2008 The Behaviour of Magnetorheological Fluids in Squeeze Mode (Dublin City University) (https://doi.org/doras.dcu.ie/547/)

[161] [161] Wang X H, Li H G and Meng G 2017 Rotordynamic coefficients of a controllable magnetorheological fluid lubricated floating ring bearing Tribol. Int. 114 1–14

[162] [162] Urreta H, Aguirre G, Kuzhir P and de Lacalle L N L 2019 Actively lubricated hybrid journal bearings based on magnetic fluids for high-precision spindles of machine tools J. Intell. Mater. Syst. Struct. 30 2257–71

[163] [163] Pan J S, Wu Y S, Zhuo Z J, Wang H, Zheng Q B and Yan Q S 2023 Experimental study of single-crystal GaN wafer electro-Fenton magnetorheological complex friction wear Tribol. Int. 180 108260

[164] [164] Zha J, Chen Y L, Zhang P H and Chen R L 2020 Effect of design parameters and operational conditions on the motion accuracy of hydrostatic thrust bearing Proc. Inst.Mech. Eng. C 234 1481–91

[165] [165] Kane N R, Sihler J and Slocum A H 2003 A hydrostatic rotary bearing with angled surface self-compensation Precis. Eng. 27 125–39

[166] [166] Zhang Y T, Lu C H, Zhao H X, Shi W J and Liang P 2019 Error averaging effect of hydrostatic journal bearings considering the influences of shaft rotating speed and external load IEEE Access 7 106346–58

[167] [167] Qi E B, Fang Z Y, Sun T, Chen J C, Liu C Z and Wang J 2016 A method for predicting hydrostatic guide error averaging effects based on three-dimensional profile error Tribol. Int.95 279–89

[168] [168] Muzakkir S M, Lijesh K P and Hirani H 2014 Tribological failure analysis of a heavily-loaded slow speed hybrid journal bearing Eng. Fail. Anal. 40 97–113

[169] [169] Zha J, Chen Y L and Zhang P H 2018 Precision design of hydrostatic thrust bearing in rotary table and spindle Proc.Inst. Mech. Eng. B 232 2044–53

[170] [170] Huang W H and Yan J W 2023 Effect of tool geometry on ultraprecision machining of soft-brittle materials: a comprehensive review Int. J. Extrem. Manuf. 5 012003

[171] [171] Zhang Y Q, Xu X D, Yang X D, Li H M, Jiang H, Yu X Y and Shi Z M 2011 Analysis on influence of oil film thickness on temperature field of heavy hydrostatic bearing in variable viscosity condition Adv. Mater. Res.239–42 1418–21

[172] [172] Liu T, Gao W G, Tian Y L, Mao K, Pan G X and Zhang D W 2015 Thermal simulation modeling of a hydrostatic machine feed platform Int. J. Adv. Manuf. Technol.79 1581–95

[173] [173] Yang S F, Li C, Jiang M L and Pei S Y 2019 A study of inlet temperature models of a large size tilting thrust bearing comparison between theory and experiment Tribol. Int.140 105881

[174] [174] Liu Z F, Zhan C P, Cheng Q, Zhao Y S, Li X Y and Wang Y D 2016 Thermal and tilt effects on bearing characteristics of hydrostatic oil pad in rotary table J.Hydrodyn. 28 585–95

[175] [175] Rowe W B 2021 Conical hydrostatic journal bearings for high speeds Proc. Inst. Mech. Eng. J 235 808–19

[176] [176] Li M Y, Chen J M and Hu Q 2014 Thermal performance analysis of conical hydrostatic bearing based on conjugate heat transfer method Mech. Res. Appl. 27 36–38, 49

[177] [177] Zhang Y Q, Sun J C, Kong P R, Kong X B and Yu X D 2019 Research on the oil film temperature field of hydrostatic bearing with variable viscosity dynamic simulation and experiment Proc. Inst. Mech. Eng. J 233 1763–72

[178] [178] Zhang Y Q, Fan L G, Li R, Dai C X and Yu X D 2013 Simulation and experimental analysis of supporting characteristics of multiple oil pad hydrostatic bearing disk J. Hydrodyn. 25 236–41

[179] [179] Shao J P, Dai C X, Zhang Y Q, Yu X D, Xu X Q and Wang Y F 2011 The effect of oil cavity depth on temperature field in heavy hydrostatic thrust bearing J.Hydrodyn. 23 676–80

[180] [180] Yu X D, Wang Y, Zhou D F, Wu G P, Zhou W K and Bi H W 2019 Heat transfer characteristics of high speed and heavy load hydrostatic bearing IEEE Access 7 110770–80

[181] [181] Yu M B, Yu X D, Zheng X H and Jiang H 2019 Thermal-fluid-solid coupling deformation of hydrostatic thrust bearing friction pairs Ind. Lubr. Tribol. 71 467–73

[182] [182] Zhang Y Q, Quan Z, Shi M, Feng H D and Liu Y L 2015 Improvement of hydrostatic bearing workbench structure based on the thermal deformation Proc. 2015 10th Int.Conf. on Computer Science & Education (IEEE) pp528–31

[183] [183] Liang X L, Liu Z Q, Wang B, Wang C J and Cheung C F 2023 Friction behaviors in the metal cutting process: state of the art and future perspectives Int. J. Extrem. Manuf. 5 012002

[184] [184] Zhang P H, Chen Y L, Zhang C Y, Zha J and Wang T 2018 Influence of geometric errors of guide rails and table on motion errors of hydrostatic guideways under quasi-static condition Int. J. Mach. Tools Manuf. 125 55–67

[185] [185] Schwenke H, Knapp W, Haitjema H, Weckenmann A,Schmitt R and Delbressine F 2008 Geometric error measurement and compensation of machines-an update CIRP Ann. 57 660–75

[186] [186] Huang W Z and Kong Z Y 2008 Simulation and integration of geometric and rigid body kinematics errors for assembly variation analysis J. Manuf. Syst. 27 36–44

[187] [187] Wang Z W, Zhao W H, Chen Y L and Lu B H 2013 Prediction of the effect of speed on motion errors in hydrostatic guideways Int. J. Mach. Tools Manuf.64 78–84

[188] [188] Zhu S Y, Sun J, Li B and Zhu G X 2020 Thermal turbulent lubrication analysis of rough surface journal bearing with journal misalignment Tribol. Int. 144 106109

[189] [189] Wang Y D, Zhao Y S, Cai L G, Liu Z F and Cheng Q 2016 Effects of thermal and hydrodynamic characteristics of heavy-duty rotary table on the hydrostatic circular pads J.Vibroeng. 18 4193–206

[190] [190] Rajput A K and Sharma S C 2016 Combined influence of geometric imperfections and misalignment of journal on the performance of four pocket hybrid journal bearing Tribol. Int. 97 59–70

[191] [191] Lv F R, Ta N and Rao Z S 2017 Analysis of equivalent supporting point location and carrying capacity of misaligned journal bearing Tribol. Int. 116 26–38

[192] [192] Jang J Y and Khonsari M M 2015 On the characteristics of misaligned journal bearings Lubricants 3 27–53

[193] [193] Wang L L, Zeng Q L, Lu C H and Liang P 2019 A numerical analysis and experimental investigation of three oil grooves sleeve bearing performance Ind. Lubr. Tribol.71 181–7

[194] [194] van Beek A and Segal A 1997 Rubber supported hydrostatic thrust bearings with rigid bearing surfaces Tribol. Int.30 47–52

[195] [195] van Beek A and Lepic L 1996 Rubber supported hydrostatic thrust bearings with elastic bearing surfaces of infinite length Wear 201 45–50

[196] [196] Michalec M, Polnick′y V, Folt′yn J, Svoboda P, ˇSperka P and Hurník J 2022 The prediction of large-scale hydrostatic bearing pad misalignment error and its compensation using compliant support Precis. Eng. 75 67–79

[197] [197] Sapirstein P 2016 Accurate measurement with photogrammetry at large sites J. Archaeol. Sci.66 137–45

[198] [198] Johns M et al 2014 Design of the giant Magellan telescope Proc. SPIE 9145 9145F

[199] [199] van Ostayen R A J, van Beek A and Ros M 2004 A mathematical model of the hydro-support: an elasto-hydrostatic thrust bearing with mixed lubrication Tribol. Int. 37 607–16

[200] [200] Niemierko A 2016 Modern bridge bearings and expansion joints for road bridges Transp. Res. Proc. 14 4040–9

[201] [201] Ahmed K, Nizami S S, Raza N Z and Mahmood K 2012 Mechanical, swelling, and thermal aging properties of marble sludge-natural rubber composites Int. J. Ind. Chem.3 21

[202] [202] Moon B, Lee J, Park S and Seok C S 2018 Study on the aging behavior of natural rubber/butadiene rubber (NR/BR) blends using a parallel spring model Polymers 10 658

[203] [203] Ben Hassine M, Na?t-Abdelaziz M, Za?ri F, Colin X,Tourcher C and Marque G 2014 Time to failure prediction in rubber components subjected to thermal ageing: a combined approach based upon the intrinsic defect concept and the fracture mechanics Mech. Mater. 79 15–24

[204] [204] Xie Z L, Ta N and Rao Z S 2017 The lubrication performance of water lubricated bearing with consideration of wall slip and inertial force J. Hydrodyn. 29 52–60

[205] [205] Wu Y Z, Zhu D, Tao R, Xiao R F and Liu W C 2022 Analysis of two-phase flow in cavitation condition of pump-turbine based on dynamic mode decomposition method in turbine mode J. Energy Storage 56 106107

[206] [206] Liang P, Lu C H, Ding J and Chen S J 2013 A method for measuring the hydrodynamic effect on the bearing land Tribol. Int. 67 146–53

[207] [207] Kim D 2016 Design space of foil bearings for closed-loop supercritical CO2 power cycles based on three-dimensional thermohydrodynamic analyses J. Eng.Gas Turbines Power 138 032504

[208] [208] Cong T L, Wang B C and Gu H Y 2022 Numerical analysis on heat transfer enhancement of sCO2 in the tube with twisted tape Nucl. Eng. Des. 397 111940

[209] [209] Bruckner R J 2009 Windage Power Loss in Gas Foil Bearings and the Rotor-Stator Clearance of High Speed Generators Operating in High Pressure Environments (NASA Glenn Research Center)

[210] [210] Preuss J L 2016 Application of hydrostatic bearings in supercritical CO2 Proc. 5th Int. Supercritical CO2 Power Cycles Symp. (San Antonio) pp 1–10

[211] [211] Palazzolo A and Shin D SCO2 bearing stiffness and damping test (available at: https://turbolab.tamu.edu/wp-content/uploads/2020/08/13-SCO2-Bearing-Stiffness-and-Damping-Test-New-Proposal.pdf)

[212] [212] Qin K, Jahn I, Gollan R and Jacobs P 2016 Development of a computational tool to simulate foil bearings for supercritical CO2 cycles J. Eng. Gas Turbines Power138 092503

[213] [213] Bi C X, Han D J, Wu Y, Li Y M and Yang J F 2021 Thermohydrodynamic investigation for supercritical carbon dioxide high speed tilting pad bearings considering turbulence and real gas effect Phys. Fluids 33 125114

[214] [214] Conboy T M 2013 Real-gas effects in foil thrust bearings operating in the turbulent regime J. Tribol. 135 031703

[215] [215] Wu Y, Yang L H, Xu T F and Wu W 2020 Thermo-elasto-hydrodynamic characteristics analysis of journal microbearing lubricated with rarefied gas Micromachines 11 955

[216] [216] Chapman P A 2018 Advanced gas foil bearing design for supercritical CO2 power cycles Proc. 6th Int. Supercritical CO2 Power Cycles Symp. (Pittsburgh, PA, USA) pp 27–29(available at: https://netl.doe.gov/sites/default/files/netlfile/Chapman-Track-B.pdf)

[217] [217] Han D J and Bi C X 2022 The partial derivative method for dynamic stiffness and damping coefficients of supercritical CO2 foil bearings Lubricants 10 307

[218] [218] Han D J, Bi C X, Chen C and Yang J F 2022 Dynamic coefficients of tilting pad bearing by perturbing the turbulence model Appl. Sci. 12 6348

[219] [219] Kim D, Ki J, Kim Y and Ahn K 2012 Extended three-dimensional thermo-hydrodynamic model of radial foil bearing: case studies on thermal behaviors and dynamic characteristics in gas turbine simulator J. Eng.Gas Turbines Power 134 052501

[220] [220] Qin K, Jacobs P A, Keep J A, Li D J and Jahn I H 2018 A fluid-structure-thermal model for bump-type foil thrust bearings Tribol. Int. 121 481–91

[221] [221] Deng Y G, Jiang Y and Liu J 2021 Low-melting-point liquid metal convective heat transfer: a review Appl. Therm. Eng.193 117021

[222] [222] Zheng A, Jia Q, Wang X and Yuan X 2010 Frequency-dependent dynamic performance of water-lubricated tilting-pad bearing based on fluid-solid-heat coupling model J. Vib. Shock 29 153–7

[223] [223] Sarafraz M M and Arjomandi M 2019 Contact angle and heat transfer characteristics of a gravity-driven film flow of a particulate liquid metal on smooth and rough surfaces Appl. Therm. Eng. 149 602–12

[224] [224] Cheng J, Yu Y, Guo J, Wang S, Zhu S Y, Ye Q, Yang J and Liu W M 2019 Ga-based liquid metal with good self-lubricity and high load-carrying capacity Tribol. Int.129 1–4

[225] [225] Ji Y L, Wu M K, Feng Y M, Liu H Q, Yang X, Li Y D and Chang C 2022 Experimental study on the effects of sodium and potassium proportions on the heat transfer performance of liquid metal high-temperature oscillating heat pipes Int. J. Heat Mass Transfer 194 123116

[226] [226] Guo J, Cheng J, Tan H, Zhu S Y, Qiao Z H, Yang J and Liu W M 2018 Ga-based liquid metal: lubrication and corrosion behaviors at a wide temperature range Materialia 4 10–19

[227] [227] Guo J, Cheng J, Tan H, Zhu S Y, Qiao Z H, Yang J and Liu W M 2019 Ga-based liquid metal: a novel current-carrying lubricant Tribol. Int. 135 457–62

[228] [228] Dobosz A, Plevachuk Y, Sklyarchuk V, Sokoliuk B, Tkach O and Gancarz T 2019 Liquid metals in cooling systems: experimental design of thermophysical properties of eutectic Ga-Sn-Zn alloy with Pb additions J. Mol. Liq.281 542–8

[229] [229] Ruan J H, Chen L X, Wang Z J, Li C X, Wu P F and Xia S G 2020 Transition mechanism based on load imbalance of liquid metal film IEEE Trans. Plasma Sci. 48 3720–6

[230] [230] Beijing Smart Beam Ltd 2021 X-ray tubes and liquid metal sliding bearings CN Patent No. 202011097286.1

[231] [231] General Electric Ltd 2012 Reinforced barrier for liquid metal bearings CN Patent No. 201110042724.9

[232] [232] General Electric Ltd 2022 Liquid metal bearing construction with reinforced seal structure CN Patent No.202210340100.3

[233] [233] Simens Ltd 2015 Liquid metal sliding bearings CN Patent No. 201410398777.8

[234] [234] Beijing Smart Beam Ltd 2019 Liquid metal bearings, x-ray tubes and anode assemblies, stators and rotors CN Patent No. 201920863087.3

[235] [235] Xie Z L and Zhu W D 2021 Rotor dynamic analysis of the vertical hydro-hybrid bearing rotor coupled system of a two-circuit main loop liquid sodium pump system Ann.Nucl. Energy 155 108139

[236] [236] Xie Z L, Shen N W, Zhu W D, Liu H L, Shi J, Wang Y K and Tian W C 2020 Dynamic characteristics analysis of the hydro-hybrid liquid sodium lubricated bearing-rotor coupled system in the two-circuit main loop liquid sodium pump system Ann. Nucl. Energy 136 107059

[237] [237] Goraj R 2018 Theoretical study on a novel electromagnetically supported hydrodynamic bearing under static loads Tribol. Int. 119 775–85

[238] [238] Olieslagers R, de Wild M, van Melick S and Knaapen R 2014 Simulation of the fluid structure interaction for an aerostatic bearing and a flexible substrate WIT Trans. Eng.Sci. 82 95–106

[239] [239] Li Y Q, Yang P and Chen W 2019 Design of liquid metal lubricated spiral groove bearing considering influences of turbulence and slip J. Xi’an Jiaotong Univ. 53 15–23

[240] [240] Xu M Y, Li Y Q and Chen W 2020 Performance analysis for liquid metal lubricated spiral groove bearings under the influence of taper error of hole machining J. Xi’an Jiaotong Univ. 54 85–92

[241] [241] Chen R G, Xie Z L, Rao Z S, Ta N, Jiao C X and Liu L 2017 Lubrication regime and dynamic characteristics of hydro-hybrid bearing of two-circuit main loop Na liquid pump system Lubr. Eng. 42 6–13

[242] [242] Yang X B 2011 Research on the Characteristics of Thermohydrodynamic Lubrication of High Speed Small Diameter Liquid Suspension Spindle and the Effect of Surface Microstructures (Hunan University)

[243] [243] Cupillard S, Glavatskih S and Cervantes M J 2008 Computational fluid dynamics analysis of a journal bearing with surface texturing Proc. Inst. Mech. Eng. J 222 97–107

[244] [244] Li X, Li Y H, Tong Z, Ma Q, Ni Y Q and Dong G N 2019 Enhanced lubrication effect of gallium-based liquid metal with laser textured surface Tribol. Int. 129 407–15

[245] [245] Mao Y Z, Yang J X and Liu Y G 2018 Analysis of influence of oil film pressure distribution of textured hydrodynamic sliding bearing Lubr. Eng. 43 55–60, 71

[246] [246] Sharma S, Jamwal G and Awasthi R K 2019 Enhancement of steady state performance of hydrodynamic journal bearing using chevron-shaped surface texture Proc. Inst. Mech.Eng. J 233 1833–43

[247] [247] Brizmer V, Kligerman Y and Etsion I 2003 A laser surface textured parallel thrust bearing Tribol. Trans.46 397–403

[248] [248] Etsion I and Burstein L 1996 A model for mechanical seals with regular microsurface structure Tribol. Trans.39 677–83

[249] [249] Etsion I, Halperin G, Brizmer V and Kligerman Y 2004 Experimental investigation of laser surface textured parallel thrust bearings Tribol. Lett. 17 295–300

[250] [250] Yan J J 2018 Rotor Dynamic Characteristics of Foil Bearing System with Surface Micro Structure (Harbin Institute of Technology)

[251] [251] Li L L, Li Y Z, Du Q W, Liu T Y and Xie Y H 2022 ReF-nets: physics-informed neural network for Reynolds equation of gas bearing Comput. Methods Appl. Mech.Eng. 391 114524

[252] [252] Chorin A J 1968 Numerical solution of the Navier-Stokes equations Math. Comput. 22 745–62

[253] [253] Wang X K, Xu Q, Wang B R, Zhang L X, Yang H and Peng Z K 2016 Effect of surface waviness on the static performance of aerostatic journal bearings Tribol. Int. 103 394–405

[254] [254] Li Y T and Ding H 2012 A simplified calculation method on the performance analysis of aerostatic thrust bearing with multiple pocketed orifice-type restrictors Tribol. Int. 56 66–71

[255] [255] Skaltsas D, Rossopoulos G N and Papadopoulos C I 2022 A comparative study of the Reynolds equation solution for slider and journal bearings with stochastic roughness on the stator and the rotor Tribol. Int. 167 107410

[256] [256] Mamori H, Fukudome K, Tanaka K and Miyazaki T 2023 Direct numerical simulation of turbulent pipe flow by large-scale control using buoyancy force Int. J. Heat Fluid Flow 99 109075

[257] [257] Lee M and Moser R D 2015 Direct numerical simulation of turbulent channel flow up to ReT ≈ 5200 J. Fluids Mech.774 395–415

[258] [258] Roshny S and Subrahamanyam D B 2022 Do the large-eddy simulations yield deeper atmospheric boundary layers in comparison to the RANs model simulations? J. Atmos.Sol.-Terr. Phys. 240 105954

[259] [259] Amani E, Ahmadpour A and Aghajari M J 2023 Large-eddy simulation of turbulent non-Newtonian flows: a comparison with state-of-the-art RANS closures Int. J.Heat Fluid Flow 99 109076

[260] [260] Xiao H, Wu J L, Wang J X, Sun R and Roy C J 2016 Quantifying and reducing model-form uncertainties in Reynolds-averaged Navier-Stokes simulations: a data-driven, physics-informed Bayesian approach J.Comput. Phys. 324 115–36

[261] [261] Sun A, Ma W Q and Wang Z W 2007 Numerical simulation of externally pressure circular thrust gas lubrication bearing under height bearing clearance Lubr. Eng.32 16–19

[262] [262] Yoshimoto S, Yamamoto M and Toda K 2007 Numerical calculations of pressure distribution in the bearing clearance of circular aerostatic thrust bearings with a single air supply inlet J. Tribol. 129 384–90

[263] [263] Li Y T and Ding H 2007 Influences of the geometrical parameters of aerostatic thrust bearing with pocketed orifice-type restrictor on its performance Tribol. Int. 40 1120–6

[264] [264] Morí?nigo J A, Anaya-Ruíz P P, Bustos A and Mayo-García R 2023 Unsteady RANs-based DMD analysis of airfoil NACA0015 with Gurney flap Int. J. Heat Fluid Flow99 109099

[265] [265] Ji B, Luo X W, Arndt R E A, Peng X X and Wu Y L 2015 Large eddy simulation and theoretical investigations of the transient cavitating vortical flow structure around a NACA66 hydrofoil Int. J. Multiph. Flow 68 121–34

[266] [266] Zhu J C, Chen H and Chen X D 2013 Large eddy simulation of vortex shedding and pressure fluctuation in aerostatic bearings J. Fluids Struct. 40 42–51

[267] [267] Liu R, Wang W M, Qi P Y and Liu B W 2013 Performance simulation and experimental study of tilting pad thrust bearing based on TEHD Chin. J. Turbomach. 7 22–27

[268] [268] Cui H L, Zhao W Y, Xia H, Yang H and Zhang L X 2015 Study on static characteristics of ultra-precision hydrostatic guideway based on numerical simulation Mod.Mach. Tool Autom. Manuf. Tech. 24–26 30

[269] [269] Ma S J, Yin Y J, Chao B, Yan K, Fang B and Hong J 2023 A real-time coupling model of bearing-rotor system based on semi-flexible body element Int. J. Mech. Sci. 245 108098

[270] [270] Lu L H, Gao Q, Chen W Q, Liu L and Wang G L 2017 Investigation on the fluid-structure interaction effect of an aerostatic spindle and the influence of structural dimensions on its performance Proc. Inst. Mech. Eng. J231 1434–40

[271] [271] Gao Q, Lu L H, Chen W Q, Chen G D and Wang G L 2017 A novel modeling method to investigate the performance of aerostatic spindle considering the fluid-structure interaction Tribol. Int. 115 461–9

[272] [272] Wang N, Wei Z Y, Lin Q Y and Chen W 2014 Multi-physical field coupling analysis of journal bearing system under time-varying condition J. Shanghai JiaoTong Univ.46 6–11

[273] [273] Hu Y and Meng Y G 2022 Performance optimization analysis of tilting pad journal bearing based on multi-physics coupling Lubr. Eng. 47 1–10

[274] [274] Gao Q, Lu L H, Zhang R, Song L Y, Huo D H and Wang G L 2019 Investigation on the thermal behavior of an aerostatic spindle system considering multi-physics coupling effect Int. J. Adv. Manuf. Technol. 102 3813–23

[275] [275] Gao S Y, Cheng K and Ding H 2014 Multi-physics simulation based design and analysis of a high speed aerostatic spindle and its performance assessment Proc.ASME 2014 Int. Design Engineering Technical Conf. and Computers and Information in Engineering Conf. (ASME)(https://doi.org/10.1115/DETC2014-34086)

[276] [276] Gao S Y, Cheng K, Ding H and Fu H Y 2016 Multiphysics-based design and analysis of the high-speed aerostatic spindle with application to micro-milling Proc.Inst. Mech. Eng. J 230 852–71

[277] [277] Chen G D, Chen Y J, Lu Q, Wu Q H and Wang M H 2020 Multi-physics fields based nonlinear dynamic behavior analysis of air bearing motorized spindle Micromachines11 723

[278] [278] Kim M S, Shim J, Kim J, Jang D G and Park S S 2020Multiphysics simulation and experiment of a thrust bearing in scroll compressors Tribol. Int. 142 105969

[279] [279] Pierson K 2019 Multiphysics Cavitation Model with Application to the Dynamic Behavior of Journal Bearings(University of Akron)

[280] [280] Badawi M B, Crosby W A, El Fahham I M and Alkomy M H 2020 Performance analysis of tilting pad journal bearing using COMSOL multiphysics and neural networks Alex.Eng. J. 59 865–81

[281] [281] Cui H L, Wang Y, Yang H, Zhou L, Li H, Wang W and Zhao C J 2018 Numerical analysis and experimental research on the angular stiffness of aerostatic bearings Tribol. Int. 120 166–78

[282] [282] Cui H L, Yue X B, Lei D J, Xia H and Zhu J P 2014 Study on radial characteristics of aerostatic bearing based on ANSYS workbench Lubr. Eng. 39 100–103

[283] [283] Yang M, Kong M, Li C H, Long Y Z, Zhang Y B, Sharma S,Li R Z, Gao T, Liu M Z and Cui X 2023 Temperature field model in surface grinding: a comparative assessment Int.J. Extrem. Manuf. 5 042011

[284] [284] Ma X Z and Zhu J 2010 Transient behavior analysis of adiabatic thermal elasto-hydrodynamic lubrication of journal bearing under step load J. Aerosp. Power 25 713–7

[285] [285] Wang S S, Guo H, Li R Z and Zhang S L 2017 Research on static characteristics of high speed hydrodynamic journal bearings affected by cavitations and thermal effect Bearing 10 36–39

[286] [286] Zhang Y, Chen G D and Wang L 2019 Effects of thermal and elastic deformations on lubricating properties of the textured journal bearing Adv. Mech. Eng. 11 1–12

[287] [287] Kang L, Zhang X N, Lou J J and Qiang L L 2020 Conjugate heat transfer study on porous media gas lubricated bearing J. Eng. Therm. Energy Power 35 158–66

[288] [288] Andre’s L S, Kim T H and Ryu K 2010 Thermal management and rotordynamic performance of a hot rotor-gas foil bearings system: part 2-predictions versus test data Proc. ASME Turbo Expo 2010: Power for Land,Sea, and Air (https://doi.org/10.1115/1.4001826) (ASME)

[289] [289] Aksoy S and Aksit M F 2015 A fully coupled 3D thermo-elastohydrodynamics model for a bump-type compliant foil journal bearing Tribol. Int. 82 110–22

[290] [290] Radil K and Batcho Z 2011 Air injection as a thermal management technique for radial foil air bearings Tribol.Trans. 54 666–73

[291] [291] Gao Q H, Sun W J, Zhang J Z and Zhang J Y 2022 Fluid-solid coupled simulation on thermal management of hydrodynamic gas foil bearing with an axial cooling throughflow Case Stud. Therm. Eng. 37 102238

[292] [292] Zhang J Y, Qiao X Y, Chen W D, Chen B X, Lyu Y W and Luo X Y 2022 Numerical investigation of thermo-aerodynamic characteristics of gas foil thrust bearing Therm. Sci. Eng. Prog. 31 101296

[293] [293] Patil T D 2013 Thermal Management Method for Foil Bearings in Turbine Hot Section (University of Texas at Arlington) (available at: https://rc.library.uta.edu/uta-ir/bitstream/handle/10106/24099/Patil_uta_2502M_12425.pdf?isAllowed=y&sequence=1)

[294] [294] Feng K, Li W J, Deng Z H and Zhang M 2017 Thermohydrodynamic analysis and thermal management of spherical spiral groove gas bearings Tribol. Trans.60 629–44

[295] [295] Martowicz A, Roemer J, Lubieniecki M, Z˙ ywica G and Bagi′nski P 2020 Experimental and numerical study on the thermal control strategy for a gas foil bearing enhanced with thermoelectric modules Mech. Syst. Signal Process.138 106581

[296] [296] Zhang G H, Liu J, Sundén B and Xie G N 2021 Combined experimental and numerical studies on flow characteristic and heat transfer in ribbed channels with vortex generators of various types and arrangements Int. J. Therm. Sci.167 107036

[297] [297] Wodtke M and Litwin W 2021 Water-lubricated stern tube bearing—experimental and theoretical investigations of thermal effects Tribol. Int. 153 106608

[298] [298] Zhang G H, Zhu R, Xie G N, Li S L and Sundén B 2022 Optimization of cooling structures in gas turbines: a review Chin. J. Aeronaut. 35 18–46

[299] [299] Zhang G H, Liu J, Sundén B and Xie G N 2020 Comparative study on the adiabatic film cooling performances with elliptical or super-elliptical holes of various length-to-width ratios Int. J. Therm. Sci. 153 106360

[300] [300] Alfares M, Saleem O and Majeed M 2019 Analytical study of thermal variation impact on dynamics of a spindle bearing system Proc. Inst. Mech. Eng. K 233 871–98

[301] [301] Zhang K, Zhao X Y, Feng K and Zhao Z L 2018 Thermohydrodynamic analysis and thermal management of hybrid bump-metal mesh foil bearings: experimental tests and theoretical predictions Int. J. Therm. Sci.127 91–104

[302] [302] Daniel G B and Cavalca K L 2013 Evaluation of the thermal effects in tilting pad bearing Int. J. Rotating Mach.2013 725268

[303] [303] Dong D, Liu G H, Xiong N, Kang J L and Wang Y 2019 Development of rotating anode targets for CT tubes Vac. Electron. 01 37–40

[304] [304] Toshiba Ltd 1993 Rotating anode x-ray tube CN Patent No.931040088.4

[305] [305] Shanghai Junan Ltd 2018 A novel heat dissipation structure of large capacity x-ray tube CN Patent No.201711222102.8

[306] [306] Toshiba Ltd 2008 Rotating anode x-ray tube assemblies CN Patent No. 931040088.4

[307] [307] Zhuhai RCAN Ltd 2018 A liquid metal bearing used for medical diagnostic x-ray tubes CN Patent Surf.201720647516.4

[308] [308] Wang X, Zhao P, Lyu B H and Yuan J L 2019 Research status of ultra-precision machining technologies for working surfaces of rolling bearings China Mech. Eng. 30 1301–9

[309] [309] Wang J S, Fang F Z, An H J, Wu S, Qi H M, Cai Y X and Guo G Y 2023 Laser machining fundamentals: micro, nano, atomic and close-to-atomic scales Int. J. Extrem.Manuf. 5 012005

[310] [310] Yang P and Chen W 2020 Analysis for performance of herringbone spiral groove thrust bearing J. Xi’an Jiaotong Univ. 54 17–27

[311] [311] Cao H R, Zhang X W and Chen X F 2017 The concept and progress of intelligent spindles: a review Int. J. Mach.Tools Manuf. 112 21–52

[312] [312] Zhu Y S, Zhang P, Yuan Q Q, Yan K and Hong J 2019 Key technologies and development trend of smart bearing J.Vib. Meas. Diagn. 39 455–62

[313] [313] Gao R X, Jin Y C and Warrington R O 1994 Microcomputer-based real-time bearing monitor IEEE Trans. Instrum. Meas. 43 216–9

[314] [314] Shao Y M, Ge L and Fang J P 2008 Fault diagnosis system based on smart bearing Proc. 2018 Int. Journal on Control, Automation and Systems (IEEE) pp 1084–9

[315] [315] Scoot S, Kovacs A, Gupta L, Katz J, Sadeghi F and Peroulis D 2011 Wireless temperature microsensors integrated on bearings for health monitoring applications Proc. 24th Int. Conf. on Micro Electro Mechanical Systems (IEEE) pp 660–3

[316] [316] Kono D, Mizuno S, Muraki T and Nakaminami M 2019 A machine tool motorized spindle with hybrid structure of steel and carbon fiber composite CIRP Ann. 68 389–92

[317] [317] Han M L, Qi Z C, Wang Z W, Zhang Q C, Sun L G and Chu B 2019 Design of intelligent temperature monitoring system for wireless bearing lubricating oil based on Arduino and NRF24l01 J. Chin. Agric. Mech. 40 167–71

[318] [318] Wang F Z, Zhu Y S, Yan K, Liu Y W and Hong J 2018 Wireless monitoring technology of rolling bearing inner ring temperature J. Mech. Eng. 54 8–14

[319] [319] Chen J H, Zhang W Y and Wang H 2021 Intelligent bearing structure and temperature field analysis based on finite element simulation for sustainable and green manufacturing J. Intell. Manuf. 32 745–56

[320] [320] Lv X H and Wang W 2021 Design of smart bearing with wireless monitoring system J. Phys.: Conf. Ser.1986 012059

[321] [321] Wang C, Cheng K, Rakowski R and Soulard J 2018 An experimental investigation on ultra-precision instrumented smart aerostatic bearing spindle applied to high speed micro-drilling J. Manuf. Process.31 324–35

[322] [322] Liu T, Gao W G, Tian Y L, Zhang D W, Zhang Y F and Chang W F 2017 Power matching based dissipation strategy onto spindle heat generations Appl. Therm. Eng.113 499–507

[323] [323] Yan R Q, Gao R X and Zhang L 2015 In-process modal parameter identification for spindle health monitoring Mechatronics 31 42–49

[324] [324] Lee C, Zolfaghari A, Kim G H and Jeon S 2019 An optical measurement technique for dynamic stiffness and damping of precision spindle system Measurement131 61–68