[1] M POLLOCK T. Alloy design for aircraft engines. Nature Materials, 15, 809-815(2016).

[2] P PADTURE N, M GELL, H JORDAN E. Thermal barrier coatings for gas-turbine engine applications. Science, 296, 280-284(2002).

[3] X LIANG, T ZHAO Y, D MA et al. Study on the preparation and microstructure of a single-crystal hollow turbine blade. Materials and Manufacturing Processes, 32, 1887-1892(2017).

[4] Z GUO, Z SONG, J FAN et al. Experimental and analytical investigation on service life of film cooling structure for single crystal turbine blade. International Journal of Fatigue, 150, 106318(2021).

[5] J LIANG, Q LIN, X ZHANG et al. Effects of alumina on cristobalite crystallization and properties of silica-based ceramic cores. Journal of Materials Science & Technology, 33, 204-209(2017).

[6] W XU, Z LU, G TIAN et al. Fabrication of single-crystal superalloy hollow blade based on integral ceramic mold. Journal of Materials Processing Technology, 271, 615-622(2019).

[7] A WALALE, S CHAUHAN A, A SATYANARAYANA et al. Analysis of shrinkage & warpage in ceramic injection molding of HPT vane leading edge core of a gas turbine casting. Materials Today: Proceedings, 5, 19471-19479(2018).

[8] S CHAUHAN A, B ANIRUDH, A SATYANARAYANA et al. FEA optimization of injection parameters in ceramic core development for investment casting of a gas turbine blade. Materials Today: Proceedings, 26, 2190-2199(2020).

[9] Q LI, W MA D, H JIANG Y. Effcet of cristoablite content on the properties of ceramic core in making directionally solidified hollow blade. Journal of Materials Engineering, 1994, 18-19.

[10] Y DONG, X LI, Q ZHAN et al. Modeling of shrinkage during investment casting of thin-walled hollow turbine blades. Journal of Materials Processing Technology, 244, 190-203(2017).

[11] M MUKHTARKHANOV, A PERVEEN, D TALAMONA. Application of stereolithography based 3D printing technology in investment casting. Micromachines, 11, 946(2020).

[12] Y PARK H, H KIM E, H CHO G et al. Process development of fabricating ceramic core using 3D printing technique. Materials Chemistry and Physics, 231, 382-387(2019).

[13] W HALLORAN J, V TOMECKOVA, S GENTRY et al. Photopolymerization of powder suspensions for shaping ceramics. Journal of the European Ceramic Society, 31, 2613-2619(2011).

[14] P GENTRY S, W HALLORAN J. Absorption effects in photopolymerized ceramic suspensions. Journal of the European Ceramic Society, 33, 1989-1994(2013).

[15] P GENTRY S, W HALLORAN J. Depth and width of cured lines in photopolymerizable ceramic suspensions. Journal of the European Ceramic Society, 33, 1981-1988(2013).

[16] V TOMECKOVA, W HALLORAN J. Cure depth for photopolymerization of ceramic suspensions. Journal of the European Ceramic Society, 30, 3023-3033(2010).

[17] V TOMECKOVA, W HALLORAN J. Predictive models for the photopolymerization of ceramic suspensions. Journal of the European Ceramic Society, 30, 2833-2840(2010).

[18] J BAE C, W HALLORAN J. Integrally cored ceramic mold fabricated by ceramic stereolithography. International Journal of Applied Ceramic Technology, 8, 1255-1262(2011).

[19] J BAE C, D KIM, W HALLORAN J. Mechanical and kinetic studies on the refractory fused silica of integrally cored ceramic mold fabricated by additive manufacturing. Journal of the European Ceramic Society, 39, 618-623(2019).

[20] H LI, Y LIU, P COLOMBO et al. The influence of sintering procedure and porosity on the properties of 3D printed alumina ceramic cores. Ceramics International, 47, 27668-27676(2021).

[21] H LI, K HU, Y LIU et al. Improved mechanical properties of silica ceramic cores prepared by 3D printing and sintering processes. Scripta Materialia, 194, 113665(2021).

[22] H LI, Y LIU, Y LIU et al. Silica strengthened alumina ceramic cores prepared by 3D printing. Journal of the European Ceramic Society, 41, 2938-2947(2021).

[23] H LI, Y LIU, Y LIU et al. Evolution of the microstructure and mechanical properties of stereolithography formed alumina cores sintered in vacuum. Journal of the European Ceramic Society, 40, 4825-4836(2020).

[24] C QIAN, K HU, Z LU et al. Volume shrinkage and conversion rate of Al₂O₃ ceramic stereolithography suspension polymerised by ultraviolet light. Materials Chemistry and Physics, 267, 124661(2021).

[25] X LI, K HU, Z LU. Effect of light attenuation on polymerization of ceramic suspensions for stereolithography. Journal of the European Ceramic Society, 39, 2503-2509(2019).

[26] C QIAN, K HU, J LI et al. The effect of light scattering in stereolithography ceramic manufacturing. Journal of the European Ceramic Society, 41, 7141-7154(2021).

[27] Q LI, X AN, J LIANG et al. Balancing flexural strength and porosity in DLP-3D printing Al₂O₃ cores for hollow turbine blades. Journal of Materials Science & Technology, 104, 19-32(2022).

[28] Q LI, J LIANG, Y ZHANG et al. Fused silica ceramic core based on network-structured zircon design via 3D printing. Scripta Materialia, 208, 114342(2022).

[29] A OLEVSKY E. Theory of sintering: from discrete to continuum. Materials Science and Engineering: R: Reports, 23, 41-100(1998).

[30] S SUNDARESAN, A AKSAY I. Mullitization of diphasic aluminosilicate gels. Journal of the American Ceramic Society, 74, 2388-2392(1991).

[31] P CAHOON H, J CHRISTENSEN C. Sintering and grain growth of alpha-alumina. Journal of the American Ceramic Society, 39, 337-344(1956).

[32] J SMOTHERS W, J REYNOLDS H. Sintering and grain growth of alumina. Journal of the American Ceramic Society, 37, 588-595(1954).

[33] Y PAN J, F LIU X, M HE L et al. Research progress of silica-base ceramic core. Foundry, 61, 174-178(2012).